TS-110に与えると、mvdsioがエラーを出して無限ループになってしまう。
そこで、もう一度ブートメッセージを見てみたが、HDDなのかSDカードなのか
分からなかった。
そこで、HDDを外してから、ブートマッサージを見てみた。
結果としては、sdioはないと思われる。
なので、kernel configからは、mvsdioは外して続けよう。
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Unknown command 'uart1' - try 'help'
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-88F6281A-BP LE
U-Boot 1.1.4 (Apr 23 2009 - 19:01:28) Marvell version: 3.4.4
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690DCC
Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
[16384kB@f8000000] Flash: 16 MB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Unknown command 'uart1' - try 'help'
## Booting image at 00800000 ...
Image Name: Linux-2.6.33.2
Created: 2012-12-05 7:14:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2083192 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux................................................................................................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.33.2 (root@VMBuildEnv001) (gcc version 4.2.1) #1 Wed Dec 5 15:14:47 CST 2012
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Feroceon-KW ARM
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/ram initrd=0xa00000,0x900000 ramdisk=32768
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 246016KB available (3784K code, 451K data, 136K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[ 0.230000] Mount-cache hash table entries: 512
[ 0.230000] CPU: Testing write buffer coherency: ok
[ 0.230000] NET: Registered protocol family 16
[ 0.230000] Feroceon L2: Enabling L2
[ 0.230000] Feroceon L2: Cache support initialised.
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e0000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] PEX1_MEM ....no such
[ 0.260000] PEX1_IO ....no such
[ 0.260000] INTER_REGS ....base f1000000, size 1MB
[ 0.260000] NFLASH_CS ....base fa000000, size 2MB
[ 0.260000] SPI_CS ....base f4000000, size 16MB
[ 0.260000] BOOT_ROM_CS ....no such
[ 0.260000] DEV_BOOTCS ....no such
[ 0.260000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.260000]
[ 0.260000] Marvell Development Board (LSP Version KW_LSP_5.1.2)-- DB-88F6281A-BP Soc: 88F6281 A1 LE
[ 0.260000]
[ 0.260000] Detected Tclk 200000000 and SysClk 400000000
[ 0.260000] MV Buttons Device Load
[ 3.280000] PEX0 interface detected no Link.
[ 3.280000] PCI: bus0: Fast back to back transfers enabled
[ 3.280000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[ 3.290000] bio: create slab <bio-0> at 0
[ 3.290000] vgaarb: loaded
[ 3.290000] SCSI subsystem initialized
[ 3.290000] usbcore: registered new interface driver usbfs
[ 3.290000] usbcore: registered new interface driver hub
[ 3.290000] usbcore: registered new interface driver ethub
[ 3.290000] usbcore: registered new device driver usb
[ 3.290000] Switching to clocksource kw_clocksource
[ 3.290000] NET: Registered protocol family 2
[ 3.290000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 3.290000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 3.290000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 3.290000] TCP: Hash tables configured (established 8192 bind 8192)
[ 3.290000] TCP reno registered
[ 3.290000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 3.290000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 3.290000] NET: Registered protocol family 1
[ 3.290000] RPC: Registered udp transport module.
[ 3.290000] RPC: Registered tcp transport module.
[ 3.290000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 3.290000] Trying to unpack rootfs image as initramfs...
[ 3.290000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 3.340000] Freeing initrd memory: 9216K
[ 3.340000] QNAP RTC initializing....
[ 3.380000] Initializing RTC is completed.
[ 3.400000] rtc kw_rtc: rtc core: registered kw-rtc as rtc0
[ 3.400000] RTC registered
[ 3.400000] watchdog_init: succeed to register misc device
[ 3.400000] Init WDT and Active SYSREST if WDT timeout
[ 3.400000] XOR registered 4 channels
[ 3.400000] XOR 2nd invalidate WA enabled
[ 3.400000] MV Buttons Driver Load
[ 3.400000] NetWinder Floating Point Emulator V0.97 (double precision)
[ 3.400000] audit: initializing netlink socket (disabled)
[ 3.400000] type=2000 audit(1362775055.000:1): initialized
[ 3.400000] VFS: Disk quotas dquot_6.5.2
[ 3.400000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.410000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 3.410000] fuse init (API version 7.13)
[ 3.410000] msgmni has been set to 499
[ 3.410000] alg: No test for stdrng (krng)
[ 3.410000] io scheduler noop registered
[ 3.410000] io scheduler deadline registered
[ 3.410000] io scheduler cfq registered (default)
[ 3.430000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.430000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 3.440000] console [ttyS0] enabled
[ 3.450000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 3.460000] brd: module loaded
[ 3.460000] loop: module loaded
[ 3.470000] qnap_pic_init: succeed to register misc device
[ 3.470000] tsinfo: create proc systemp successfully
[ 3.480000] tsinfo: create proc systemp successfully
[ 3.480000] tsinfo: create proc systemp successfully
[ 3.490000] tsinfo: create proc systemp successfully
[ 3.490000] serial8250_PIC_init..uartclk = 200000000,baudDivisor = 651,irq = 34
[ 3.500000] Integrated Sata device found
[ 3.510000] IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
[ 5.550000] Spin up ...(0:0)
[ 7.560000] Spin up ...(0:1)
[ 9.560000] Spin up all...
[ 12.560000] [0 0]: Waiting for channel initialization.
[ 13.570000] [0 1]: Waiting for channel initialization.
[ 14.570000] scsi0 : Marvell SCSI to SATA adapter
[ 14.580000] scsi1 : Marvell SCSI to SATA adapter
[ 14.590000] SPI Serial flash detected @ 0xf4000000, 16384KB (64sec x 256KB)
[ 14.600000] Creating 6 MTD partitions on "spi_flash":
[ 14.600000] 0x000000000000-0x000000080000 : "U-Boot"
[ 14.610000] 0x000000200000-0x000000400000 : "Kernel"
[ 14.610000] 0x000000400000-0x000000d00000 : "RootFS"
[ 14.620000] 0x000000d00000-0x000001000000 : "RootFS2"
[ 14.620000] 0x000000080000-0x0000000c0000 : "U-Boot Config"
[ 14.630000] 0x0000000c0000-0x000000200000 : "NAS Config"
[ 14.640000] Loading Marvell Ethernet Driver:
[ 14.640000] o Cached descriptors in DRAM
[ 14.640000] o DRAM SW cache-coherency
[ 14.650000] o 1 Giga ports supported
[ 14.650000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 14.660000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 14.660000] o TCP segmentation offload (TSO) supported
[ 14.670000] o Large Receive offload (LRO) supported
[ 14.670000] o Receive checksum offload supported
[ 14.680000] o Transmit checksum offload supported
[ 14.680000] o Network Fast Processing (Routing) supported - (Disabled)
[ 14.690000] o Proc tool API enabled
[ 14.690000] o SKB Reuse supported - (Disabled)
[ 14.700000] o SKB Recycle supported - (Disabled)
[ 14.700000] o Rx descripors: q0=128
[ 14.710000] o Tx descripors: q0=532
[ 14.710000] o Loading network interface(s):
[ 14.720000] o register under mv88fx_eth platform
[ 14.720000] o eth0, ifindex = 2, GbE port = 0
[ 14.730000]
[ 14.730000] mvFpRuleDb (00000010): 0 entries, 0 bytes
[ 14.730000] Marvell debug tracing is on
[ 14.740000] Initializing USB Mass Storage driver...
[ 14.740000] usbcore: registered new interface driver usb-storage
[ 14.750000] USB Mass Storage support registered.
[ 14.750000] usb: create proc systemp successfully
[ 14.760000] usb: create proc systemp successfully
[ 14.760000] mice: PS/2 mouse device common for all mice
[ 14.770000] md: linear personality registered for level -1
[ 14.770000] md: raid0 personality registered for level 0
[ 14.780000] md: raid1 personality registered for level 1
[ 14.790000] TCP cubic registered
[ 14.790000] NET: Registered protocol family 17
[ 14.810000] rtc kw_rtc: setting system clock to 2013-03-08 20:37:47 UTC (1362775067)
[ 14.820000] md: Waiting for all devices to be available before autodetect
[ 14.830000] md: If you don't use raid, use raid=noautodetect
[ 14.830000] md: Autodetecting RAID arrays.
[ 14.840000] md: Scanned 0 and added 0 devices.
[ 14.840000] md: autorun ...
[ 14.850000] md: ... autorun DONE.
[ 14.850000] RAMDISK: gzip image found at block 0
[ 16.180000] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 16.190000] Freeing init memory: 136K
[ 16.640000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 16.650000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 16.650000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 16.690000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 16.710000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 16.710000] hub 1-0:1.0: USB hub found
[ 16.720000] hub 1-0:1.0: 1 port detected
Start config_util...
config_util: No initialized HD exists.
[ 17.040000] usb 1-1: new high speed USB device using orion-ehci and address 2
config_util: No initialized HD exists.
Some errors occurred while running config_util.
config_util finished.
mount HDD root device
mount /dev/md9 failed.
[ 17.200000] hub 1-1:1.0: USB hub found
[ 17.200000] hub 1-1:1.0: 4 ports detected
bootcmd check ok
Update Extended rcX_init.d...(2)
dd: /dev/sda4: Invalid argument
Extract RootFS Ext...
default: 0xa1
Power recovery is on
[ 30.030000] xor: measuring software checksum speed
[ 30.080000] arm4regs : 726.800 MB/sec
[ 30.130000] 8regs : 550.800 MB/sec
[ 30.180000] 32regs : 618.000 MB/sec
[ 30.180000] xor: using function: arm4regs (726.800 MB/sec)
[ 30.380000] raid6: int32x1 61 MB/s
[ 30.550000] raid6: int32x2 82 MB/s
[ 30.720000] raid6: int32x4 83 MB/s
[ 30.890000] raid6: int32x8 76 MB/s
[ 30.890000] raid6: using algorithm int32x4 (83 MB/s)
[ 31.040000] md: raid6 personality registered for level 6
[ 31.040000] md: raid5 personality registered for level 5
[ 31.050000] md: raid4 personality registered for level 4
[ 31.130000] device-mapper: ioctl: 4.16.0-ioctl (2009-11-05) initialised: dm-devel@redhat.com
[ 31.320000] cryptodev: driver 0.9 loaded.
[ 31.410000] usbcore: registered new interface driver usbhid
[ 31.410000] usbhid: USB HID core driver
[ 31.450000] usbcore: registered new interface driver usblp
[ 31.490000] sysinfo: Module loaded.
[ 31.670000] fnotify: module license 'non-GPL' taints kernel.
[ 31.680000] Disabling lock debugging due to kernel taint
[ 31.720000] fnotify: Load file notify kernel module.
[ 31.730000] fnotify: Global_Private_Data_List_Init()
[ 31.730000] fnotify: Launch the fnotify thread: 710
[ 31.740000] fnotify: The fnotify thread starts...
[ 31.800000] Enable WDT...
[ 34.060000] eth0: mac address changed
[ 34.090000] eth0: link down
[ 34.100000] eth0: started
MAC_ADDR 00:08:9B:BF:F8:22
mount: /dev/sda1 is not a valid block device
log hidden config directory not exist, initial log file...
Initialize database...
Done. Return value is 0
Set max number of logs to 50
Done. Return value is 0
Initialize database...
Done. Return value is 0
Set max number of logs to 50
Done. Return value is 0
[ 35.740000] eth0: link up, full duplex, speed 100 Mbps
NIC 1 Link is Up
init_netlink_socket error!
storage_boot_init 3 ...
storage_boot_init.c: booting without HD
storage_boot_init 4 ...
storage_boot_init.c: Set Status LED...
[/sys/block/sda]
[ 39.830000] eth0: stopped
eth0 DHCP
[ 41.030000] eth0: link down
[ 41.030000] eth0: started
[ 44.220000] eth0: link up, full duplex, speed 100 Mbps
sh: /sbin/lcd_tool: No such file or directory
default: 0xa2
upnpd[1318]: UPnP SDK Successfully Initialized.
upnpd[1318]: Succesfully set the Web Server Root Directory.
upnpd[1318]: IGD root device successfully registered.
sh: /sbin/lcd_tool: No such file or directory
NASBFF822
killall: snmpd: no process killed
Stopping network...
Shutting down upnpd services:1317 1318
.
[ 67.430000] eth0: stopped
/etc/rcS.d/S45network: line 580: /etc/init.d/vlan.sh: No such file or directory
Stopped.
Starting network...eth0 DHCP
[ 69.320000] eth0: link down
[ 69.330000] eth0: started
[ 70.940000] eth0: link up, full duplex, speed 100 Mbps
Shutting down winbindd services:Shutting down upnpd services:killall: upnpcd: no process killed
winbindd.
killall: snmpd: no process killed
Starting winbindd services:1317 1318
.
Starting upnpd: get eth0 gateway = 192.168.81.1
sh: /usr/bin/qcmd: No such file or directory
upnpd[1946]: UPnP SDK Successfully Initialized.
upnpd[1946]: Succesfully set the Web Server Root Directory.
upnpd[1946]: IGD root device successfully registered.
default via 192.168.81.1 dev eth0
.
upnpd[1946]: Advertisements Sent. Listening for requests ...
[ 87.990000] eth0: stopped
[ 88.020000] eth0: link down
[ 88.020000] eth0: started
Starting thttpd services:[ 89.660000] eth0: link up, full duplex, speed 100 Mbps
thttpd.
Starting Qthttpd services:Default share Web is not found. Apache httpd start failed.
config_util: No initialized HD exists.
init_check.sh: No HD existed.
Starting sshd services: sshd.
Starting telnet services: disabled.
Starting opentftpd services: disabled.
Starting stunnel services: /bin/cp: cannot create regular file `/etc/config/stunnel/backup.cert': No such file or directory
/bin/cp: cannot create regular file `/etc/config/stunnel/backup.key': No such file or directory
stunnel.
Shutting down bonjour services:cat: /var/lock/bonjour.normal: No such file or directory
mDNSResponderPosix
Starting bonjour services: mDNSResponderPosix.
1317 1318 1945 1946
[ 100.590000] warning: process `pic_raw' used the deprecated sysctl system call with 8.1.2.
sed: /home/httpd/cgi-bin/Qrecordings/help/*.html: No such file or directory
sed: /home/httpd/help/inc/app/*.js: No such file or directory
sed: /home/httpd/cgi-bin/inc/*.js: No such file or directory
sed: /home/httpd/cgi-bin/inc/*.js: No such file or directory
/etc/init.d/genLanglist.sh: line 46: /home/httpd/ajax_obj/extjs/languages.js: No such file or directory
/etc/init.d/genLanglist.sh: line 47: /home/httpd/ajax_obj/extjs/languages.js: No such file or directory
sss_convert...[pass]
killall: snmpd: no process killed
/etc/init.d/usb_device_check.sh: line 25: /usr/sbin/lsusb: No such file or directory
Welcome to TS-110(192.168.81.95), QNAP Systems, Inc.
NASBFF822 login:
0 件のコメント:
コメントを投稿
注: コメントを投稿できるのは、このブログのメンバーだけです。