NetBSD on 初代HP MicroServer

Debian GNU/Linux armel 7.1でQnap TS-110をNFS serverにしていたのだが、7.0の時はSunOS/SolarisからNFS mountできたのに、7.1にしたらmountできなくなってしまった。
Debianのbug reportをするにも良く分からないし、そもそもNetBSDにしたかったので、NetBSD/evbearm-el 6.99.23を試してみたが、buildが通らなかったり、/sbin/initが異常終了したりと、使えない。evbarmはそもそもbuildが通らなかった。

1週間ばかりいろいろ試みたがだめだったので、とくださんの情報をもとに、Amazon.co.jpでlHP MicroServerとRemote Access Cardを購入した。
来たので、NetBSD/amd64 6.1.1を入れるがディスクアクセスが以上に遅く、pkgsrc.tar.gzを展開するのに1500秒くらいかかってしまう。その間のほとんどはフリーズしている。
BIOSを見直すと、drive write cacheが無効になっていたので、有効にすると、pkgsrc.tar.gzの展開に150秒くらいと、まあ我慢できる性能になった。bufq strategyをうたがっってみたが、それは関係なかったらしい。また、SB700 AHCI Controllerの問題でもなかったらしい。

順調に稼働中。

ディスプレイもキーボードもつながずにインストールできるRemote Access Cardはとても便利だった。やっぱりちゃんとしたサーバーを使うに限る。

Remote Access Cardのウェブインターフェイスは、http://IPADDRESS/ でアクセスしないとログインできない場合がある。http://IPADDRESS/login.html では駄目なようだ。


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.

NetBSD 6.1.1 (GENERIC)
total memory = 2047 MB
avail memory = 1972 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
HP ProLiant MicroServer ( )
mainbus0 (root)
cpu0 at mainbus0 apid 0: AMD Turion(tm) II Neo N54L Dual-Core Processor, id 0x100f63
cpu1 at mainbus0 apid 1: AMD Turion(tm) II Neo N54L Dual-Core Processor, id 0x100f63
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 21, 24 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <HP ,ProLiant,20110729>, AslId <HP ,00000097>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
BROD (PNP0C02) at acpi0 not configured
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
OMSC (PNP0C02) at acpi0 not configured
RMSC (PNP0C02) at acpi0 not configured
PCIE (PNP0C02) at acpi0 not configured
RMEM (PNP0C01) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x1022 product 0x9601 (rev. 0x00)
ppb0 at pci0 dev 4 function 0: vendor 0x1022 product 0x9604 (rev. 0x00)
ppb0: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci1 dev 0 function 0: vendor 0x1a03 product 0x1150 (rev. 0x02)
ppb1: PCI Express 1.0 <PCI-E to PCI/PCI-X Bridge>
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci2 dev 0 function 0: vendor 0x1a03 product 0x2000 (rev. 0x10)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
ppb2 at pci0 dev 6 function 0: vendor 0x1022 product 0x9606 (rev. 0x00)
ppb2: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci3 dev 0 function 0: Broadcom BCM5723 Gigabit Ethernet
bge0: interrupting at ioapic0 pin 18
bge0: adjust device control 0x192000 -> 0x195000
bge0: ASIC BCM5784 A1 (0x5784100), Ethernet address c8:cb:b8:c9:67:12
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5784 10/100/1000baseT PHY, rev. 4
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ahcisata0 at pci0 dev 17 function 0: vendor 0x1002 product 0x4391 (rev. 0x40)
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.20, 4 ports, 32 slots, CAP 0xf722ff03<PSC,SSC,PMD,SPM,ISS=0x2=Gen2,SCLO,SAL,SALP,SMPS,SSNTF,SNCQ,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 2
atabus3 at ahcisata0 channel 3
ohci0 at pci0 dev 18 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 18
ohci0: OHCI version 1.0, legacy support
ohci0: SMM does not respond, resetting
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 18 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci0: interrupting at ioapic0 pin 17
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controller, 5 ports each: ohci0
usb1 at ehci0: USB revision 2.0
ohci1 at pci0 dev 19 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 18
ohci1: OHCI version 1.0, legacy support
ohci1: SMM does not respond, resetting
usb2 at ohci1: USB revision 1.0
ehci1 at pci0 dev 19 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci1: interrupting at ioapic0 pin 17
ehci1: dropped intr workaround enabled
ehci1: EHCI version 1.0
ehci1: companion controller, 5 ports each: ohci1
usb3 at ehci1: USB revision 2.0
piixpm0 at pci0 dev 20 function 0: vendor 0x1002 product 0x4385 (rev. 0x42)
piixpm0: polling (SB800)
iic0 at piixpm0: I2C bus
ixpide0 at pci0 dev 20 function 1: ATI Technologies IXP IDE Controller (rev. 0x40)
ixpide0: bus-master DMA support present
ixpide0: primary channel configured to compatibility mode
ixpide0: primary channel interrupting at ioapic0 pin 14
atabus4 at ixpide0 channel 0
ixpide0: secondary channel configured to compatibility mode
ixpide0: secondary channel interrupting at ioapic0 pin 15
atabus5 at ixpide0 channel 1
pcib0 at pci0 dev 20 function 3: vendor 0x1002 product 0x439d (rev. 0x40)
ppb3 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x40)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled
ohci2 at pci0 dev 22 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2: OHCI version 1.0, legacy support
usb4 at ohci2: USB revision 1.0
ehci2 at pci0 dev 22 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci2: interrupting at ioapic0 pin 17
ehci2: dropped intr workaround enabled
ehci2: EHCI version 1.0
ehci2: companion controller, 4 ports each: ohci2
usb5 at ehci2: USB revision 2.0
pchb1 at pci0 dev 24 function 0: vendor 0x1022 product 0x1200 (rev. 0x00)
pchb2 at pci0 dev 24 function 1: vendor 0x1022 product 0x1201 (rev. 0x00)
pchb3 at pci0 dev 24 function 2: vendor 0x1022 product 0x1202 (rev. 0x00)
pchb4 at pci0 dev 24 function 3: vendor 0x1022 product 0x1203 (rev. 0x00)
amdtemp0 at pchb4: AMD CPU Temperature Sensors (Family10h)
pchb5 at pci0 dev 24 function 4: vendor 0x1022 product 0x1204 (rev. 0x00)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbc: cmd word write error
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: HLT, lat 0 us, pow 0 mW
acpicpu0: P0: FFH, lat 4 us, pow 10575 mW, 2200 MHz
acpicpu0: P1: FFH, lat 4 us, pow 8030 mW, 1900 MHz
acpicpu0: P2: FFH, lat 4 us, pow 5842 mW, 1600 MHz
acpicpu0: P3: FFH, lat 4 us, pow 4085 mW, 1300 MHz
acpicpu0: P4: FFH, lat 4 us, pow 2062 mW, 800 MHz
acpicpu0: T0: I/O, lat 1 us, pow 0 mW, 100 %
acpicpu0: T1: I/O, lat 1 us, pow 0 mW, 88 %
acpicpu0: T2: I/O, lat 1 us, pow 0 mW, 76 %
acpicpu0: T3: I/O, lat 1 us, pow 0 mW, 64 %
acpicpu0: T4: I/O, lat 1 us, pow 0 mW, 52 %
acpicpu0: T5: I/O, lat 1 us, pow 0 mW, 40 %
acpicpu0: T6: I/O, lat 1 us, pow 0 mW, 28 %
acpicpu0: T7: I/O, lat 1 us, pow 0 mW, 16 %
acpicpu1 at cpu1: ACPI CPU
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 2196456260 Hz quality 3000
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 5 ports with 5 removable, self powered
uhub1 at usb1: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 5 ports with 5 removable, self powered
uhub2 at usb2: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 5 ports with 5 removable, self powered
uhub3 at usb3: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 5 ports with 5 removable, self powered
uhub4 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 4 ports with 4 removable, self powered
uhub5 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 4 ports with 4 removable, self powered
ahcisata0 port 0: device present, speed: 3.0Gb/s
wd0 at atabus0 drive 0
wd0: <VB0250EAVER>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
uhidev0 at uhub3 port 2 configuration 1 interface 0
uhidev0: Avocent USB Composite Device-0, rev 2.00/0.00, addr 2, iclass 3/1
ukbd0 at uhidev0
wskbd0 at ukbd0 mux 1
wskbd0: connecting to wsdisplay0
uhidev1 at uhub3 port 2 configuration 1 interface 1
uhidev1: Avocent USB Composite Device-0, rev 2.00/0.00, addr 2, iclass 3/1
ums0 at uhidev1: 3 buttons and Z dir
wsmouse0 at ums0 mux 0
uhidev2 at uhub3 port 2 configuration 1 interface 2
uhidev2: Avocent USB Composite Device-0, rev 2.00/0.00, addr 2, iclass 3/1
ums1 at uhidev2: 3 buttons and Z dir
wsmouse1 at ums1 mux 0
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex, playback, capture
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
cprng kernel: WARNING pseudorandom rekeying.

Comments

Popular posts from this blog

#5000へCメールを送れないau端末でezweb.ne.jpの電子メールアドレスをIMAP4/SMTPで扱う方法

Vaio Pro 11/13用のサードパーティーのACアダプター

Windows 7 Professional用のNFSクライアントを使う (NFS 4.1のみ)