Arch BSDをVirtualBoxにインストールする
細かい所で良く分からない部分はあるものの、だいたい使えるように
なって来た。
けれども、Debian GNU/kFreeBSDだけを対象にするのはちょっと
残念かもしれないと思う。他にもGentoo FreeBSDとかArch BSDとか、
FreeBSDを利用するプロジェクトはあるので、それも似た構造であれば
サポートするようにしたい。
Gentoo FreeBSDは、http://wiki.gentoo.org/wiki/Gentoo_FreeBSD に、
SONAMEの違いくらいしか違いがないと書いてある。
つまりFreeBSDのlibcを使っていると言うことのようである。
Arch BSDについては、何も情報がないので、実際に試してみることにした。
私の仮想マシンはメモリーが少ないので、ZFSなんて無理なので、UFSで設定する。
基本的には、Official Arch BSD Install Guide
http://wiki.archbsd.net/index.php/Official_Arch_BSD_Install_Guide
の通りにすれば良いのだが、これがSCSIディスク(da)を前提に書いているのと、
root filesystemの指定が追加で必要だったので、以下に手順をまとめておく。
まずは、ISOイメージをダウンロードする。Arch BSDのオフィシャルサイトには
書いてないようだったが、2013-05-03版が出ているので、以下のURLから
取得する。
ftp://archbsd.net/iso/2013-05-03/ArchBSD-x86_64-03052013.iso
VirtualBoxは、OS:FreeBSD(64bit)、IO APIC有効、ハードウェアクロックをUTCにする
を有効にし、今回はストレージコントローラーは、SATA AHCIにした。
IDEでも以下の記述は当てはまるのではないかと思う。
ネットワークアダプターは、Intel PRO 82540EMにしたが、何でも問題なく
動くだろう。
適当な大きさのHDDファイルを用意して、ISOイメージから起動する。
ユーザー名: root、パスワードなしでログインする。
私は、US配列のキーボードを使うので、kdbmapとかは使わないし、
framebufferも使わないので、vidcontrolも触らない。
ディスクをGPTで設定する。
# gpart create -s gpt ada0
ブートローダーの置き場になると思われる領域を準備する。
これが、/dev/ada0p1になる。
# gpart add -s 64k freebsd-boot ada0
スワップ領域を1GB用意する。
これが、/dev/ada0p2になる。
# gpart add -s 1g -t freebsd-swap ada0
ルートパーティションを用意する。大きさは残り全部。
これが、/dev/ada0p3になる。
# gpart add -t freebsd-ufs ada0
ブートローダーをインストールする。ada0p1にインストールされるようだ(-i 1)。
# gpart bootcode -b /boot/pmbr -p /boot/gptboot -i 1 ada0
ルートパーティションada0p3をnewfs(フォーマット)する。
# newfs -U -j -L root /dev/ada0p3
スワップを有効にする。
# swapon /dev/ada0p2
ベースシステムをインストールするために、仮に/mntにmountする。
# mount /dev/ada0p3 /mnt
DHCPサーバーにIPアドレスとかを割り当ててもらう。
自宅が手動固定IP制になっていたら、DHCP/DDNS環境を整えると良い。
# dhclient em0
ベースシステムをインストールする。
# pacstrap /mnt base
chrootして、環境を整える。
# chroot /mnt
root filesystemを指定する。ここはOfficial Install Guideにはないが
私には必要だった。
/boot/loader.confに、以下のように書き足す。
# vi /boot/loader.conf
vfs.root.mountfrom="ufs:/dev/ada0p3"
/etc/fstabを以下のように書く。
# vi /etc/fatab
/dev/ada0p2 none swap sw 0 0
/dev/ada0p3 / ufs rw 1 1
タイムゾーンを合わせる。以下は日本の場合。
# ln -s /usr/share/zoneinfo/Asia/Tokyo /etc/localtime
ホスト名を設定する。
# vi /etc/conf.d/hostname
hostname="yourhostname"
rootのパスワードを設定する。
# passwd
そのままrebootコマンドでリブートしても良いし、chrootから抜けて、
/mntをumountしてrebootしても良い。
で、結局のところ、Arch BSDはGentoo FreeBSDのようなもので、glibc/eglibcを
使ってはいないようである。
NetBSD ftp (tnftp)でhttp proxyを使う
DNSサーバーはないので、全てをhttp proxyに喰わせてやらないといけない。
$ export http_proxy=http://USERNAME:PASSWORD@10.0.0.1:8080/
としておいて、
$ ftp http://example.com/test.tar.gz
とかすると、無事にfetchできる。この時のために、http://ftp.jp.NetBSD.org/ を用意しておいたようなものだ。
NetBSDで「12ステップで作る組込みOS自作入門」を実践する
しばらく前に、「12ステップで作る組込みOS自作入門」坂井弘亮著(以下、12ステップ本)と、 それに必要な、H8/3069Fネット対応マイコンLANボード (完成品)、 シリアルストレートケーブル、 スイッチング電源を買って来た。 ただ、引っ越しし立てなのもあって、触れないでいた。
今週になって、NetBSD/amd64 currentで開発環境を整える気分になったので、 以下のように用意してみた。
pkgsrc/cross/h8300-elf-binutils 12ステップ本の使っている2.19.1を素直にパッケージにしたもの。
pkgsrc/cross/h8300-elf-gcc34 同じく使われている3.4.6をパッケージにしたもの。 12ステップ本ではnewlibは使っていないが、別にbuildしてある分には 困らないようなので、gcc 3.4.6の頃のnewlibである1.14.0と 組み合わせてある。
pkgsrc/misc/kz_h8write h8writeが全く反応しないのに困っていたところ、 とくださんに教えていただいたライター。h8writeと違ってH8/8039にしか 対応していないが、今回の用途では困らない。
使っているNetBSDマシンは、MacBook Air 11-inch (mid 2012)なので、 当然のようにserial portはない。uftdi(4)なケーブルでつないで、 書き込みもシリアルへの出力もできた。
NetBSD/evbarm on Qnap TS-110のNFS rootでのブートメッセージ
分からなかったのだが、root device: とプロンプトが出た時に、
mvgbe0を指定してやれば良いと気づいた。
DHCPサーバーの設定と一緒に一連の流れを掲載しておく。
NetBSDでサポートしてほしくて、send-prもしてある。
http://mail-index.NetBSD.org/netbsd-bugs/2013/03/09/msg032363.html
http://gnats.NetBSD.org/47637
DHCPサーバーのdhcpd.confの抜粋
root-pathを指定してあると、それを使ってくれるのは、NetBSD/hp700や
NetBSD/sparc64のnetbootと一緒だ。
host phosphorus {
hardware ethernet 00:50:43:3c:3b:5d;
fixed-address 192.168.81.125;
ddns-hostname "phosphorus";
filename "F_TS-110_netbsd.ub";
next-server 192.168.81.249;
option root-path "/export/ts110";
}
u-bootから、loginプロンプトまでの一連の流れ
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-88F6281A-BP LE
U-Boot 1.1.4 (Apr 23 2009 - 19:01:28) Marvell version: 3.4.4
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690DCC
Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
[16384kB@f8000000] Flash: 16 MB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
QNAP: Recovery Button pressed: 0
Marvell>> dhcp
BOOTP broadcast 1
Bootfile Prefix: F_TS-110
DHCP client bound to address 192.168.81.125
Marvell>> tftp
Using egiga0 device
TFTP from server 192.168.81.249; our IP address is 192.168.81.125
Filename 'F_TS-110_netbsd.ub'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####################################
done
Bytes transferred = 4844992 (49edc0 hex)
Marvell>> bootm
## Booting image at 02000000 ...
Image Name: NetBSD/qnapts110 6.99.17
Created: 2013-03-08 12:15:57 UTC
Image Type: ARM NetBSD Kernel Image (uncompressed)
Data Size: 4844928 Bytes = 4.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Transferring control to NetBSD stage-2 loader (at address 00008000) ...
NetBSD/evbarm (qnapts110) booting ...
[ Kernel symbol table missing! ]
Loaded initial symtab at 0xc03d94d0, strtab at 0xc0412b8c, # entries 14617
pmap_postinit: Allocated 35 static L1 descriptor tables
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.99.17 (QNAPTS110) #9: Fri Mar 8 21:15:55 JST 2013
root@tellurium.elements.tetera.org:/usr/obj-evbarm/sys/arch/evbarm/compile/QNAPTS110
total memory = 256 MB
avail memory = 245 MB
cprng kernel: WARNING insufficient entropy at creation.
mainbus0 (root)
cpu0 at mainbus0 core 0: Sheeva 88SV131 rev 1 (ARM9E-S V5TE core)
cpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled
cpu0: 16KB/32B 4-way L1 Instruction cache
cpu0: 16KB/32B 4-way write-back-locking-C L1 Data cache
mvsoc0 at mainbus0: Marvell 88F6281 Rev. A1 Kirkwood
mvsoc0: CPU Clock 800.000 MHz SysClock 400.000 MHz TClock 200.000 MHz
mvsoctmr0 at mvsoc0 unit 0 offset 0x20300-0x203ff: Marvell SoC Timer
mvsocgpp0 at mvsoc0 unit 0 offset 0x10100-0x101ff irq 35: Marvell SoC General Purpose I/O Port Interface
mvsocgpp0: 50 gpio pins
mvsocgpp0: interrupts 96..103, intr 35
mvsocgpp0: interrupts 104..111, intr 36
mvsocgpp0: interrupts 112..119, intr 37
mvsocgpp0: interrupts 120..127, intr 38
mvsocgpp0: interrupts 128..135, intr 39
mvsocgpp0: interrupts 136..143, intr 40
mvsocgpp0: interrupts 144..151, intr 41
mvsocgpp0: Data Out: 0x00000000
mvsocgpp0: Data Out Enable Control: 0x00012000
mvsocgpp0: Data Blink Enable: 0x00000000
mvsocgpp0: Data In Polarity: 0x00000000
mvsocgpp0: Data In: 0x00010000
mvsocgpp0: Interrupt Cause: 0x00000000
mvsocgpp0: Interrupt Mask: 0x00000000
mvsocgpp0: Interrupt Level Mask: 0x00000000
mvsocgpp0: High Data Out: 0x0000000c
mvsocgpp0: High Data Out Enable Ctrl: 0xffffffd3
mvsocgpp0: High Blink Enable: 0x00000000
mvsocgpp0: High Data In Polarity: 0x00000000
mvsocgpp0: High Data In: 0x0000004c
mvsocgpp0: High Interrupt Cause: 0x00000000
mvsocgpp0: High Interrupt Mask: 0x00000000
mvsocgpp0: High Interrupt Level Mask: 0x00000000
gpio0 at mvsocgpp0: 50 pins
mvsocrtc at mvsoc0 unit 0 not configured
com0 at mvsoc0 unit 0 offset 0x12000-0x1201f irq 33: ns16550a, working fifo
com0: console
com1 at mvsoc0 unit 1 offset 0x12100-0x1211f irq 34: ns16550a, working fifo
ehci0 at mvsoc0 unit 0 offset 0x50000-0x51fff irq 19: Marvell USB 2.0 Interface
usb0 at ehci0: USB revision 2.0
gtidmac0 at mvsoc0 unit 0 offset 0x60000-0x60fff: Marvell IDMA Controller/XOR Engine
gtidmac0: XOR Engine 4 channels, intr 5...8
gttwsi0 at mvsoc0 unit 0 offset 0x11000-0x110ff irq 29: Marvell TWSI controller
iic0 at gttwsi0: I2C bus
s390rtc0 at iic0 addr 0x30: Seiko Instruments 35390A Real-time Clock
mvcesa0 at mvsoc0 unit 0 offset 0x30000-0x3ffff irq 22: Marvell Cryptographic Engines and Security Accelerator
mvgbec0 at mvsoc0 unit 0 offset 0x70000-0x73fff: Marvell Gigabit Ethernet Controller
mvgbe0 at mvgbec0 port 0 irq 11
mvgbe0: Ethernet address 00:50:43:3c:3b:5d
makphy0 at mvgbe0 phy 8: Marvell 88E1116R Gigabit PHY, rev. 0
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
mvsoc0: mvgbec1 clock disabled
mvpex0 at mvsoc0 unit 0 offset 0x40000-0x41fff irq 9: Marvell PCI Express Interface
pci0 at mvpex0
WARNING: module error: vfs load failed 45 for `pciverbose'
WARNING: module error: vfs load failed 45 for `pciverbose'
vendor 0x11ab product 0x6281 (miscellaneous memory, revision 0x03) at pci0 dev 0 function 0 not configured
mvsata0 at mvsoc0 unit 0 offset 0x80000-0x87fff irq 21: Marvell Serial-ATA Host Controller (SATAHC)
mvsata0: GenIIe, 1hc, 2port/hc
atabus0 at mvsata0 channel 0
atabus1 at mvsata0 channel 1
mvsdio at mvsoc0 unit 0 not configured
uhub0 at usb0: Marvell EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1 at uhub0 port 1: Genesys Logic USB2.0 Hub, class 9/0, rev 2.00/77.60, addr 2
uhub1: single transaction translator
cprng sysctl: WARNING insufficient entropy at creation.
boot device: <unknown>
root device:
use one of: mvgbe0 ddb halt reboot
root device: mvgbe0
dump device:
file system (default generic):
root on mvgbe0
mountroot: trying nfs...
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: 192.168.81.249
nfs_boot: my_domain=elements.tetera.org
nfs_boot: my_addr=192.168.81.125
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=192.168.81.1
root on 192.168.81.249:/export/ts110
root time: 0x513b353a
root file system type: nfs
warning: no /dev/console
init path (default /sbin/init):
init: copying out path `/sbin/init' 11
Sat Mar 9 13:12:30 UTC 2013
Not checking /: fs_passno = 0 in /etc/fstab
Starting file system checks:
random_seed: /var/db/entropy-file: Not present
WARNING: module error: vfs load failed 78 for `compat'
WARNING: module error: vfs load failed 78 for `compat'
WARNING: module error: vfs load failed 78 for `compat'
WARNING: module error: vfs load failed 78 for `compat'
Setting tty flags.
Setting sysctl variables:
ddb.onpanic: 1 -> 0
Starting network.
IPv6 mode: host
Configuring network interfaces:.
Adding interface aliases:.
Waiting for DAD completion for statically configured addresses...
Starting dhcpcd.
Building databases: dev, utmp, utmpx.
Starting syslogd.
cprng 292411d30: WARNING insufficient entropy at creation.
Mounting all filesystems...
Clearing temporary files.
Creating a.out runtime link editor directory cache.
Checking quotas: done.
Setting securelevel: kern.securelevel: 0 -> 1
/etc/rc: WARNING: No swap space configured!
/etc/rc.d/swap2 exited with code 1
Starting virecover.
Checking for core dump...
savecore: no core dump (no dumpdev)
Starting local daemons:.
Updating motd.
/usr/sbin/postconf: warning: valid_hostname: empty hostname
/usr/sbin/postconf: fatal: unable to use my own hostname
Mar 9 13:12:53 postfix[539]: fatal: unable to use my own hostname
/etc/rc.d/postfix exited with code 1
Starting inetd.
Starting cron.
The following components reported failures:
/etc/rc.d/swap2 /etc/rc.d/postfix
See /var/run/rc.log for more information.
Sat Mar 9 13:12:55 UTC 2013
NetBSD/evbarm (Amnesiac) (console)
login:
TS-110でのNetBSDのブートメッセージ
言う話を、
http://karuppuswamy.com/wordpress/2012/04/20/how-to-get-scheduled-power-on-feature-working-in-debian-gnulinux-for-qnap-ts-110-server/
で読んだので、kernel configに、
src/sys/arch/evbarm/conf/OPENBLOCKS_A6にあるのを真似て、
s390rtc* at iic0 addr 0x30
と書いたところ、認識したように見える。
まだuserlandまでたとり着いていないので、ちゃんと動いているかテストはできない。
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-88F6281A-BP LE
U-Boot 1.1.4 (Apr 23 2009 - 19:01:28) Marvell version: 3.4.4
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690DCC
Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
[16384kB@f8000000] Flash: 16 MB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
QNAP: Recovery Button pressed: 0
Marvell>> setenv serverip 192.168.81.249
Marvell>> setenv ipaddr 192.168.81.10
Marvell>> setenv netmask 255.255.255.0
Marvell>> tftp 100000 netbsd.ub
Using egiga0 device
TFTP from server 192.168.81.249; our IP address is 192.168.81.10
Filename 'netbsd.ub'.
Load address: 0x100000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####################################
done
Bytes transferred = 4844992 (49edc0 hex)
Marvell>> bootm
## Booting image at 00100000 ...
Image Name: NetBSD/qnapts110 6.99.17
Created: 2013-03-08 12:15:57 UTC
Image Type: ARM NetBSD Kernel Image (uncompressed)
Data Size: 4844928 Bytes = 4.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Transferring control to NetBSD stage-2 loader (at address 00008000) ...
NetBSD/evbarm (qnapts110) booting ...
[ Kernel symbol table missing! ]
Loaded initial symtab at 0xc03d94d0, strtab at 0xc0412b8c, # entries 14617
pmap_postinit: Allocated 35 static L1 descriptor tables
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.99.17 (QNAPTS110) #9: Fri Mar 8 21:15:55 JST 2013
root@tellurium.elements.tetera.org:/usr/obj-evbarm/sys/arch/evbarm/compile/QNAPTS110
total memory = 256 MB
avail memory = 245 MB
cprng kernel: WARNING insufficient entropy at creation.
mainbus0 (root)
cpu0 at mainbus0 core 0: Sheeva 88SV131 rev 1 (ARM9E-S V5TE core)
cpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled
cpu0: 16KB/32B 4-way L1 Instruction cache
cpu0: 16KB/32B 4-way write-back-locking-C L1 Data cache
mvsoc0 at mainbus0: Marvell 88F6281 Rev. A1 Kirkwood
mvsoc0: CPU Clock 800.000 MHz SysClock 400.000 MHz TClock 200.000 MHz
mvsoctmr0 at mvsoc0 unit 0 offset 0x20300-0x203ff: Marvell SoC Timer
mvsocgpp0 at mvsoc0 unit 0 offset 0x10100-0x101ff irq 35: Marvell SoC General Purpose I/O Port Interface
mvsocgpp0: 50 gpio pins
mvsocgpp0: interrupts 96..103, intr 35
mvsocgpp0: interrupts 104..111, intr 36
mvsocgpp0: interrupts 112..119, intr 37
mvsocgpp0: interrupts 120..127, intr 38
mvsocgpp0: interrupts 128..135, intr 39
mvsocgpp0: interrupts 136..143, intr 40
mvsocgpp0: interrupts 144..151, intr 41
mvsocgpp0: Data Out: 0x00000000
mvsocgpp0: Data Out Enable Control: 0x00012000
mvsocgpp0: Data Blink Enable: 0x00000000
mvsocgpp0: Data In Polarity: 0x00000000
mvsocgpp0: Data In: 0x00010000
mvsocgpp0: Interrupt Cause: 0x00000000
mvsocgpp0: Interrupt Mask: 0x00000000
mvsocgpp0: Interrupt Level Mask: 0x00000000
mvsocgpp0: High Data Out: 0x0000000c
mvsocgpp0: High Data Out Enable Ctrl: 0xffffffd3
mvsocgpp0: High Blink Enable: 0x00000000
mvsocgpp0: High Data In Polarity: 0x00000000
mvsocgpp0: High Data In: 0x0000004c
mvsocgpp0: High Interrupt Cause: 0x00000000
mvsocgpp0: High Interrupt Mask: 0x00000000
mvsocgpp0: High Interrupt Level Mask: 0x00000000
gpio0 at mvsocgpp0: 50 pins
mvsocrtc at mvsoc0 unit 0 not configured
com0 at mvsoc0 unit 0 offset 0x12000-0x1201f irq 33: ns16550a, working fifo
com0: console
com1 at mvsoc0 unit 1 offset 0x12100-0x1211f irq 34: ns16550a, working fifo
ehci0 at mvsoc0 unit 0 offset 0x50000-0x51fff irq 19: Marvell USB 2.0 Interface
usb0 at ehci0: USB revision 2.0
gtidmac0 at mvsoc0 unit 0 offset 0x60000-0x60fff: Marvell IDMA Controller/XOR Engine
gtidmac0: XOR Engine 4 channels, intr 5...8
gttwsi0 at mvsoc0 unit 0 offset 0x11000-0x110ff irq 29: Marvell TWSI controller
iic0 at gttwsi0: I2C bus
s390rtc0 at iic0 addr 0x30: Seiko Instruments 35390A Real-time Clock
mvcesa0 at mvsoc0 unit 0 offset 0x30000-0x3ffff irq 22: Marvell Cryptographic Engines and Security Accelerator
mvgbec0 at mvsoc0 unit 0 offset 0x70000-0x73fff: Marvell Gigabit Ethernet Controller
mvgbe0 at mvgbec0 port 0 irq 11
mvgbe0: Ethernet address 00:50:43:3c:3b:5d
makphy0 at mvgbe0 phy 8: Marvell 88E1116R Gigabit PHY, rev. 0
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
mvsoc0: mvgbec1 clock disabled
mvpex0 at mvsoc0 unit 0 offset 0x40000-0x41fff irq 9: Marvell PCI Express Interface
pci0 at mvpex0
WARNING: module error: vfs load failed 45 for `pciverbose'
WARNING: module error: vfs load failed 45 for `pciverbose'
vendor 0x11ab product 0x6281 (miscellaneous memory, revision 0x03) at pci0 dev 0 function 0 not configured
mvsata0 at mvsoc0 unit 0 offset 0x80000-0x87fff irq 21: Marvell Serial-ATA Host Controller (SATAHC)
mvsata0: GenIIe, 1hc, 2port/hc
atabus0 at mvsata0 channel 0
atabus1 at mvsata0 channel 1
mvsdio at mvsoc0 unit 0 not configured
uhub0 at usb0: Marvell EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1 at uhub0 port 1: Genesys Logic USB2.0 Hub, class 9/0, rev 2.00/77.60, addr 2
uhub1: single transaction translator
cprng sysctl: WARNING insufficient entropy at creation.
boot device: <unknown>
root device:
# $NetBSD: SHEEVAPLUG,v 1.29 2013/03/02 02:42:12 christos Exp $
#
# This configuration supports for generically Marvell SheevaPlug
#
include "arch/evbarm/conf/std.marvell"
options INCLUDE_CONFIG_FILE # embed config file in kernel binary
# estimated number of users
maxusers 32
# Board Type
makeoptions BOARDTYPE="qnapts110"
options EVBARM_BOARDTYPE=qnapts110
# CPU options
options CPU_SHEEVA
#options MV_L2_CACHE_ENABLE
#options MV_L2_CACHE_WRITE_THROUGH
options MV_CACHE_RANGE_OPS
makeoptions CPUFLAGS="-march=armv5te"
# Marvell SoC options
options KIRKWOOD
# Standard system options
options MSGBUFSIZE=32768
options RTC_OFFSET=0 # hardware clock is this many mins. west of GMT
#options NTP # NTP phase/frequency locked loop
# File systems
file-system FFS # UFS
file-system EXT2FS # second extended file system (linux)
#file-system LFS # log-structured file system
#file-system MFS # memory file system
file-system NFS # Network File System client
#file-system NTFS # Windows/NT file system (experimental)
#file-system CD9660 # ISO 9660 + Rock Ridge file system
file-system MSDOSFS # MS-DOS file system
file-system FDESC # /dev/fd
file-system KERNFS # /kern
#file-system NULLFS # loopback file system
#file-system OVERLAY # overlay file system
file-system PROCFS # /proc
file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs)
#file-system UMAPFS # NULLFS + uid and gid remapping
#file-system UNION # union file system
#file-system CODA # Coda File System; also needs vcoda (below)
#file-system SMBFS # experimental - CIFS; also needs nsmb (below)
file-system PTYFS # /dev/ptm support
file-system TMPFS # Efficient memory file-system
#file-system UDF # experimental - OSTA UDF CD/DVD file-system
#file-system HFS # experimental - Apple HFS+ (read-only)
# File system options
#options QUOTA # legacy UFS quotas
#options QUOTA2 # new, in-filesystem UFS quotas
#options FFS_EI # FFS Endian Independent support
options WAPBL # File system journaling support
# Note that UFS_DIRHASH is suspected of causing kernel memory corruption.
# It is not recommended for general use.
#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental
options NFSSERVER # Network File System server
options FFS_NO_SNAPSHOT # No FFS snapshot support
#options EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and
# immutable) behave as system flags.
# Networking options
#options GATEWAY # packet forwarding
options INET # IP + ICMP + TCP + UDP
options INET6 # IPv6
#options IPSEC # IP security
#options IPSEC_NAT_T # IPsec NAT traversal (NAT-T)
#options IPSEC_DEBUG # debug for IP security
#options MROUTING # IP multicast routing
#options PIM # Protocol Independent Multicast
#options NETATALK # AppleTalk networking protocols
#options PPP_BSDCOMP # BSD-Compress compression support for PPP
#options PPP_DEFLATE # Deflate compression support for PPP
#options PPP_FILTER # Active filter support for PPP (requires bpf)
#options PFIL_HOOKS # pfil(9) packet filter hooks
#options IPFILTER_LOG # ipmon(8) log support
#options IPFILTER_LOOKUP # ippool(8) support
#options IPFILTER_COMPAT # Compat for IP-Filter
#options IPFILTER_DEFAULT_BLOCK # block all packets by default
#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG
#options INET_CSUM_COUNTERS
#options TCP_CSUM_COUNTERS
#options UDP_CSUM_COUNTERS
#options MVGBE_EVENT_COUNTERS
#options NFS_BOOT_BOOTP
options NFS_BOOT_DHCP
#options NFS_BOOT_BOOTPARAM
# Compatibility options
#options COMPAT_09 # NetBSD 0.9 compatibility.
#options COMPAT_10 # NetBSD 1.0 compatibility.
#options COMPAT_11 # NetBSD 1.1 compatibility.
#options COMPAT_12 # NetBSD 1.2 compatibility.
#options COMPAT_13 # NetBSD 1.3 compatibility.
#options COMPAT_14 # NetBSD 1.4 compatibility.
#options COMPAT_15 # NetBSD 1.5 compatibility.
#options COMPAT_16 # NetBSD 1.6 compatibility.
#options COMPAT_20 # NetBSD 2.0 compatibility.
#options COMPAT_30 # NetBSD 3.0 compatibility.
#options COMPAT_40 # NetBSD 4.0 compatibility.
options COMPAT_50 # NetBSD 5.0 compatibility.
options COMPAT_60 # NetBSD 6.0 compatibility.
#options COMPAT_43 # 4.3BSD compatibility.
#options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended.
options COMPAT_OSSAUDIO # OSS (Voxware) audio driver compatibility
options COMPAT_LINUX # binary compatibility with Linux
options COMPAT_BSDPTY # /dev/[pt]ty?? ptys.
# Shared memory options
options SYSVMSG # System V-like message queues
options SYSVSEM # System V-like semaphores
options SYSVSHM # System V-like memory sharing
# Device options
#options MEMORY_DISK_HOOKS # boottime setup of ramdisk
#options MEMORY_DISK_IS_ROOT # use memory disk as root
#options MEMORY_DISK_DYNAMIC
#options MEMORY_DISK_ROOT_SIZE=22528 # Size in blocks
#options MEMORY_RBFLAGS=RB_AUTOBOOT
options DKWEDGE_AUTODISCOVER
options DKWEDGE_METHOD_GPT
# Miscellaneous kernel options
options KTRACE # system call tracing, a la ktrace(1)
options IRQSTATS # manage IRQ statistics
#options LKM # loadable kernel modules
#options KMEMSTATS # kernel memory statistics
options MIIVERBOSE # Verbose MII autoconfuration messages
#options PCIVERBOSE # Verbose PCI descriptions
options USBVERBOSE # verbose USB device autoconfig messages
#options DDB_KEYCODE=0x40
#options USERCONF # userconf(4) support
#options PIPE_SOCKETPAIR # smaller, but slower pipe(2)
#options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel
# Development and Debugging options
#options PERFCTRS # performance counters
options DIAGNOSTIC # internally consistency checks
options DEBUG
#options LOCKDEBUG
#options PMAP_DEBUG # Enable pmap_debug_level code
#options VERBOSE_INIT_ARM # verbose bootstraping messages
options DDB # in-kernel debugger
#options DDB_HISTORY_SIZE=100 # Enable history editing in DDB
#options KGDB
#options DEBUG_KGDB
makeoptions DEBUG="-g" # compile full symbol table
#makeoptions COPTS="-O1"
options SYMTAB_SPACE=800000
#options AUDIO_DEBUG=2
config netbsd root on ? type ?
# The main bus device
mainbus0 at root
# The boot cpu
cpu0 at mainbus?
# Marvell MV88F6xxx Kirkwood System-on-chip
mvsoc0 at mainbus?
# On-chip PCI Express Interface
mvpex* at mvsoc? offset ? irq ?
# PCI bus support
options PCI_NETBSD_CONFIGURE
#options PCI_CONFIG_DUMP # verbosely dump PCI config space
pci* at mvpex?
pchb* at pci? dev ? function ? # PCI-Host bridges
# On-chip Serial-ATA II Host Controller (SATAHC)
mvsata* at mvsoc? offset ? irq ?
# On-chip Gigabit Ethernet Controller Interface
mvgbec* at mvsoc? offset ?
mvgbe* at mvgbec? port ? irq ?
# MII/PHY support
makphy* at mii? phy ?
# On-chip USB 2.0 Interface
ehci* at mvsoc? offset ? irq ?
# On-chip Cryptographic Engines and Security Accelerator
mvcesa* at mvsoc? offset ? irq ?
# On-chip Two-Wire Serial Interface (TWSI)
gttwsi* at mvsoc? offset ? irq ?
iic* at gttwsi?
s390rtc* at iic0 addr 0x30
# On-chip UART Interface
com* at mvsoc? offset ? irq ?
# On-chip IDMA Controller
gtidmac* at mvsoc? offset ? irq ?
# On-chip General Purpose I/O Port Interface
mvsocgpp* at mvsoc? offset ? irq ?
gpio* at mvsocgpp?
# On-chip Timers
mvsoctmr* at mvsoc? offset ? irq ?
# ATA (IDE) bus support
atabus* at ata?
#options ATADEBUG
# IDE drives
wd* at atabus? drive ? flags 0x0000
# ATAPI bus support
atapibus* at atapi?
# ATAPI devices
# flags have the same meaning as for IDE drives.
cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives
sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives
# USB bus support
usb* at ehci?
# USB Hubs
uhub* at usb?
uhub* at uhub? port ?
# USB HID device
uhidev* at uhub? port ? configuration ? interface ?
# USB Mice
ums* at uhidev? reportid ?
wsmouse* at ums? mux 0
# USB eGalax touch-panel
uep* at uhub? port ?
wsmouse* at uep? mux 0
# USB Keyboards
ukbd* at uhidev? reportid ?
wskbd* at ukbd? console ? mux 1
# USB TEMPer and TEMPerHUM
uthum* at uhidev? reportid ?
# USB serial adapter
ucycom* at uhidev? reportid ?
# USB Generic HID devices
uhid* at uhidev? reportid ?
# USB LCDs and USB-VGA adaptors
udl* at uhub? port ? # DisplayLink DL-1x0/1x5
wsdisplay* at udl?
# USB Printer
ulpt* at uhub? port ? configuration ? interface ?
# USB Modem
umodem* at uhub? port ? configuration ?
ucom* at umodem?
# Option N.V. Wireless WAN modems
uhso* at uhub? port ? configuration ?
# USB Mass Storage
umass* at uhub? port ? configuration ? interface ?
wd* at umass?
scsibus* at scsi?
sd* at scsibus? target ? lun ? # SCSI disk drives
cd* at scsibus? target ? lun ? # SCSI CD-ROM drives
# USB audio
uaudio* at uhub? port ? configuration ?
# USB MIDI
umidi* at uhub? port ? configuration ?
# USB IrDA
# USB-IrDA bridge spec
uirda* at uhub? port ? configuration ? interface ?
irframe* at uirda?
stuirda* at uhub? port ? configuration ? interface ?
irframe* at stuirda?
# SigmaTel STIr4200 USB/IrDA Bridge
ustir* at uhub? port ?
irframe* at ustir?
# USB Ethernet adapters
aue* at uhub? port ? # ADMtek AN986 Pegasus based adapters
axe* at uhub? port ? # ASIX AX88172 based adapters
cdce* at uhub? port ? # CDC, Ethernet Networking Control Model
cue* at uhub? port ? # CATC USB-EL1201A based adapters
kue* at uhub? port ? # Kawasaki LSI KL5KUSB101B based adapters
udav* at uhub? port ? # Davicom DM9601 based adapters
url* at uhub? port ? # Realtek RTL8150L based adapters
# USB 802.11 adapters
atu* at uhub? port ? # Atmel AT76C50XX based adapters
ural* at uhub? port ? # Ralink Technology RT2500USB 802.11a/b/g
rum* at uhub? port ? # Ralink Technology RT2501/RT2601 802.11a/b/g
zyd* at uhub? port ? # Zydas ZD1211
# Prolific PL2301/PL2302 host-to-host adapter
upl* at uhub? port ?
# Serial adapters
ubsa* at uhub? port ? # Belkin serial adapter
ucom* at ubsa? portno ?
uchcom* at uhub? port ? # WinChipHead CH341/CH340 serial adapter
ucom* at uchcom? portno ?
uftdi* at uhub? port ? # FTDI FT8U100AX serial adapter
ucom* at uftdi? portno ?
uipaq* at uhub? port ? # iPAQ PDAs
ucom* at uipaq? portno ?
umct* at uhub? port ? # MCT USB-RS232 serial adapter
ucom* at umct? portno ?
uplcom* at uhub? port ? # I/O DATA USB-RSAQ2 serial adapter
ucom* at uplcom? portno ?
uslsa* at uhub? port ? # Silicon Labs USB-RS232 serial adapter
ucom* at uslsa? portno ?
uvscom* at uhub? port ? # SUNTAC Slipper U VS-10U serial adapter
ucom* at uvscom? portno ?
# RIM BlackBerry
uberry* at uhub? port ?
# Diamond Multimedia Rio 500
urio* at uhub? port ?
# USB Handspring Visor
uvisor* at uhub? port ?
ucom* at uvisor?
# Kyocera AIR-EDGE PHONE
ukyopon* at uhub? port ?
ucom* at ukyopon? portno ?
# USB scanners
uscanner* at uhub? port ?
# USB scanners that use SCSI emulation, e.g., HP5300
usscanner* at uhub? port ?
# Topfield TF5000PVR range of DVB recorders
utoppy* at uhub? port ?
# Y@P firmware loader
uyap* at uhub? port ?
# D-Link DSB-R100 USB radio
udsbr* at uhub? port ?
radio* at udsbr?
# USB Generic driver
ugen* at uhub? port ?
# USB 3G datacards
u3ginit* at uhub? port ?
u3g* at uhub? port ?
ucom* at u3g?
# USB generic serial port (e.g., data over cellular)
ugensa* at uhub? port ?
ucom* at ugensa?
# Bluetooth Controller and Device support
# Bluetooth USB Controllers
ubt* at uhub? port ?
aubtfwl* at uhub? port ?
# Bluetooth Device Hub
bthub* at ubt?
# Bluetooth HID support
bthidev* at bthub?
# Bluetooth Mouse
btms* at bthidev? reportid ?
wsmouse* at btms? mux 0
# Bluetooth Keyboard
btkbd* at bthidev? reportid ?
wskbd* at btkbd? console ? mux 1
# Bluetooth Apple Magic Mouse
btmagic* at bthub?
wsmouse* at btmagic? mux 0
# Bluetooth Audio support
btsco* at bthub?
# Audio support
audio* at audiobus?
# Pseudo-Devices
pseudo-device crypto # /dev/crypto device
pseudo-device swcrypto # software crypto implementation
# disk/mass storage pseudo-devices
#pseudo-device bio # RAID control device driver
#pseudo-device ccd 4 # concatenated/striped disk devices
#pseudo-device cgd 4 # cryptographic disk devices
#pseudo-device raid 8 # RAIDframe disk driver
#options RAID_AUTOCONFIG # auto-configuration of RAID components
# Options to enable various other RAIDframe RAID types.
#options RF_INCLUDE_EVENODD=1
#options RF_INCLUDE_RAID5_RS=1
#options RF_INCLUDE_PARITYLOGGING=1
#options RF_INCLUDE_CHAINDECLUSTER=1
#options RF_INCLUDE_INTERDECLUSTER=1
#options RF_INCLUDE_PARITY_DECLUSTERING=1
#options RF_INCLUDE_PARITY_DECLUSTERING_DS=1
pseudo-device fss # file system snapshot device
pseudo-device putter # for puffs and pud
#pseudo-device md # memory disk device (ramdisk)
pseudo-device vnd # disk-like interface to files
options VND_COMPRESSION # compressed vnd(4)
# network pseudo-devices
pseudo-device bpfilter # Berkeley packet filter
#pseudo-device carp # Common Address Redundancy Protocol
#pseudo-device ipfilter # IP filter (firewall) and NAT
pseudo-device loop # network loopback
#pseudo-device ppp # Point-to-Point Protocol
#pseudo-device pppoe # PPP over Ethernet (RFC 2516)
#pseudo-device sl # Serial Line IP
#pseudo-device strip # Starmode Radio IP (Metricom)
#pseudo-device irframetty # IrDA frame line discipline
pseudo-device tap # virtual Ethernet
#pseudo-device tun # network tunneling over tty
#pseudo-device gre # generic L3 over IP tunnel
#pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC 1933)
#pseudo-device faith # IPv[46] TCP relay translation i/f
pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation
#pseudo-device vlan # IEEE 802.1q encapsulation
#pseudo-device bridge # simple inter-network bridging
#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too
#pseudo-device agr # IEEE 802.3ad link aggregation
#pseudo-device pf # PF packet filter
#pseudo-device pflog # PF log if
# miscellaneous pseudo-devices
pseudo-device pty # pseudo-terminals
#pseudo-device sequencer 1 # MIDI sequencer
#options RND_COM
pseudo-device clockctl # user control of clock subsystem
pseudo-device ksyms # /dev/ksyms
pseudo-device drvctl # device control
# a pseudo device needed for Coda # also needs CODA (above)
#pseudo-device vcoda 4 # coda minicache <-> venus comm.
# a pseudo device needed for SMBFS
#pseudo-device nsmb # experimental - SMB requester
# wscons pseudo-devices
#pseudo-device wsmux # mouse & keyboard multiplexor
#pseudo-device wsfont
# data mover pseudo-devices
pseudo-device swdmover # software dmover(9) back-end
pseudo-device dmoverio # /dev/dmover dmover(9) interface
#options FILEASSOC # fileassoc(9) - required for Veriexec
# Veriexec
#pseudo-device veriexec
#
# Uncomment the fingerprint methods below that are desired. Note that
# removing fingerprint methods will have almost no impact on the kernel
# code size.
#
#options VERIFIED_EXEC_FP_RMD160
#options VERIFIED_EXEC_FP_SHA256
#options VERIFIED_EXEC_FP_SHA384
#options VERIFIED_EXEC_FP_SHA512
#options VERIFIED_EXEC_FP_SHA1
#options VERIFIED_EXEC_FP_MD5
#options PAX_MPROTECT=0 # PaX mprotect(2) restrictions
#options PAX_ASLR=0 # PaX Address Space Layout Randomization
TS-110のHDDなしの場合のブートメッセージ
TS-110に与えると、mvdsioがエラーを出して無限ループになってしまう。
そこで、もう一度ブートメッセージを見てみたが、HDDなのかSDカードなのか
分からなかった。
そこで、HDDを外してから、ブートマッサージを見てみた。
結果としては、sdioはないと思われる。
なので、kernel configからは、mvsdioは外して続けよう。
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Unknown command 'uart1' - try 'help'
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-88F6281A-BP LE
U-Boot 1.1.4 (Apr 23 2009 - 19:01:28) Marvell version: 3.4.4
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690DCC
Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
[16384kB@f8000000] Flash: 16 MB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Unknown command 'uart1' - try 'help'
## Booting image at 00800000 ...
Image Name: Linux-2.6.33.2
Created: 2012-12-05 7:14:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2083192 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux................................................................................................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.33.2 (root@VMBuildEnv001) (gcc version 4.2.1) #1 Wed Dec 5 15:14:47 CST 2012
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Feroceon-KW ARM
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/ram initrd=0xa00000,0x900000 ramdisk=32768
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 246016KB available (3784K code, 451K data, 136K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[ 0.230000] Mount-cache hash table entries: 512
[ 0.230000] CPU: Testing write buffer coherency: ok
[ 0.230000] NET: Registered protocol family 16
[ 0.230000] Feroceon L2: Enabling L2
[ 0.230000] Feroceon L2: Cache support initialised.
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e0000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] PEX1_MEM ....no such
[ 0.260000] PEX1_IO ....no such
[ 0.260000] INTER_REGS ....base f1000000, size 1MB
[ 0.260000] NFLASH_CS ....base fa000000, size 2MB
[ 0.260000] SPI_CS ....base f4000000, size 16MB
[ 0.260000] BOOT_ROM_CS ....no such
[ 0.260000] DEV_BOOTCS ....no such
[ 0.260000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.260000]
[ 0.260000] Marvell Development Board (LSP Version KW_LSP_5.1.2)-- DB-88F6281A-BP Soc: 88F6281 A1 LE
[ 0.260000]
[ 0.260000] Detected Tclk 200000000 and SysClk 400000000
[ 0.260000] MV Buttons Device Load
[ 3.280000] PEX0 interface detected no Link.
[ 3.280000] PCI: bus0: Fast back to back transfers enabled
[ 3.280000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[ 3.290000] bio: create slab <bio-0> at 0
[ 3.290000] vgaarb: loaded
[ 3.290000] SCSI subsystem initialized
[ 3.290000] usbcore: registered new interface driver usbfs
[ 3.290000] usbcore: registered new interface driver hub
[ 3.290000] usbcore: registered new interface driver ethub
[ 3.290000] usbcore: registered new device driver usb
[ 3.290000] Switching to clocksource kw_clocksource
[ 3.290000] NET: Registered protocol family 2
[ 3.290000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 3.290000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 3.290000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 3.290000] TCP: Hash tables configured (established 8192 bind 8192)
[ 3.290000] TCP reno registered
[ 3.290000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 3.290000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 3.290000] NET: Registered protocol family 1
[ 3.290000] RPC: Registered udp transport module.
[ 3.290000] RPC: Registered tcp transport module.
[ 3.290000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 3.290000] Trying to unpack rootfs image as initramfs...
[ 3.290000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 3.340000] Freeing initrd memory: 9216K
[ 3.340000] QNAP RTC initializing....
[ 3.380000] Initializing RTC is completed.
[ 3.400000] rtc kw_rtc: rtc core: registered kw-rtc as rtc0
[ 3.400000] RTC registered
[ 3.400000] watchdog_init: succeed to register misc device
[ 3.400000] Init WDT and Active SYSREST if WDT timeout
[ 3.400000] XOR registered 4 channels
[ 3.400000] XOR 2nd invalidate WA enabled
[ 3.400000] MV Buttons Driver Load
[ 3.400000] NetWinder Floating Point Emulator V0.97 (double precision)
[ 3.400000] audit: initializing netlink socket (disabled)
[ 3.400000] type=2000 audit(1362775055.000:1): initialized
[ 3.400000] VFS: Disk quotas dquot_6.5.2
[ 3.400000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.410000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 3.410000] fuse init (API version 7.13)
[ 3.410000] msgmni has been set to 499
[ 3.410000] alg: No test for stdrng (krng)
[ 3.410000] io scheduler noop registered
[ 3.410000] io scheduler deadline registered
[ 3.410000] io scheduler cfq registered (default)
[ 3.430000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.430000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 3.440000] console [ttyS0] enabled
[ 3.450000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 3.460000] brd: module loaded
[ 3.460000] loop: module loaded
[ 3.470000] qnap_pic_init: succeed to register misc device
[ 3.470000] tsinfo: create proc systemp successfully
[ 3.480000] tsinfo: create proc systemp successfully
[ 3.480000] tsinfo: create proc systemp successfully
[ 3.490000] tsinfo: create proc systemp successfully
[ 3.490000] serial8250_PIC_init..uartclk = 200000000,baudDivisor = 651,irq = 34
[ 3.500000] Integrated Sata device found
[ 3.510000] IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
[ 5.550000] Spin up ...(0:0)
[ 7.560000] Spin up ...(0:1)
[ 9.560000] Spin up all...
[ 12.560000] [0 0]: Waiting for channel initialization.
[ 13.570000] [0 1]: Waiting for channel initialization.
[ 14.570000] scsi0 : Marvell SCSI to SATA adapter
[ 14.580000] scsi1 : Marvell SCSI to SATA adapter
[ 14.590000] SPI Serial flash detected @ 0xf4000000, 16384KB (64sec x 256KB)
[ 14.600000] Creating 6 MTD partitions on "spi_flash":
[ 14.600000] 0x000000000000-0x000000080000 : "U-Boot"
[ 14.610000] 0x000000200000-0x000000400000 : "Kernel"
[ 14.610000] 0x000000400000-0x000000d00000 : "RootFS"
[ 14.620000] 0x000000d00000-0x000001000000 : "RootFS2"
[ 14.620000] 0x000000080000-0x0000000c0000 : "U-Boot Config"
[ 14.630000] 0x0000000c0000-0x000000200000 : "NAS Config"
[ 14.640000] Loading Marvell Ethernet Driver:
[ 14.640000] o Cached descriptors in DRAM
[ 14.640000] o DRAM SW cache-coherency
[ 14.650000] o 1 Giga ports supported
[ 14.650000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 14.660000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 14.660000] o TCP segmentation offload (TSO) supported
[ 14.670000] o Large Receive offload (LRO) supported
[ 14.670000] o Receive checksum offload supported
[ 14.680000] o Transmit checksum offload supported
[ 14.680000] o Network Fast Processing (Routing) supported - (Disabled)
[ 14.690000] o Proc tool API enabled
[ 14.690000] o SKB Reuse supported - (Disabled)
[ 14.700000] o SKB Recycle supported - (Disabled)
[ 14.700000] o Rx descripors: q0=128
[ 14.710000] o Tx descripors: q0=532
[ 14.710000] o Loading network interface(s):
[ 14.720000] o register under mv88fx_eth platform
[ 14.720000] o eth0, ifindex = 2, GbE port = 0
[ 14.730000]
[ 14.730000] mvFpRuleDb (00000010): 0 entries, 0 bytes
[ 14.730000] Marvell debug tracing is on
[ 14.740000] Initializing USB Mass Storage driver...
[ 14.740000] usbcore: registered new interface driver usb-storage
[ 14.750000] USB Mass Storage support registered.
[ 14.750000] usb: create proc systemp successfully
[ 14.760000] usb: create proc systemp successfully
[ 14.760000] mice: PS/2 mouse device common for all mice
[ 14.770000] md: linear personality registered for level -1
[ 14.770000] md: raid0 personality registered for level 0
[ 14.780000] md: raid1 personality registered for level 1
[ 14.790000] TCP cubic registered
[ 14.790000] NET: Registered protocol family 17
[ 14.810000] rtc kw_rtc: setting system clock to 2013-03-08 20:37:47 UTC (1362775067)
[ 14.820000] md: Waiting for all devices to be available before autodetect
[ 14.830000] md: If you don't use raid, use raid=noautodetect
[ 14.830000] md: Autodetecting RAID arrays.
[ 14.840000] md: Scanned 0 and added 0 devices.
[ 14.840000] md: autorun ...
[ 14.850000] md: ... autorun DONE.
[ 14.850000] RAMDISK: gzip image found at block 0
[ 16.180000] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 16.190000] Freeing init memory: 136K
[ 16.640000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 16.650000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 16.650000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 16.690000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 16.710000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 16.710000] hub 1-0:1.0: USB hub found
[ 16.720000] hub 1-0:1.0: 1 port detected
Start config_util...
config_util: No initialized HD exists.
[ 17.040000] usb 1-1: new high speed USB device using orion-ehci and address 2
config_util: No initialized HD exists.
Some errors occurred while running config_util.
config_util finished.
mount HDD root device
mount /dev/md9 failed.
[ 17.200000] hub 1-1:1.0: USB hub found
[ 17.200000] hub 1-1:1.0: 4 ports detected
bootcmd check ok
Update Extended rcX_init.d...(2)
dd: /dev/sda4: Invalid argument
Extract RootFS Ext...
default: 0xa1
Power recovery is on
[ 30.030000] xor: measuring software checksum speed
[ 30.080000] arm4regs : 726.800 MB/sec
[ 30.130000] 8regs : 550.800 MB/sec
[ 30.180000] 32regs : 618.000 MB/sec
[ 30.180000] xor: using function: arm4regs (726.800 MB/sec)
[ 30.380000] raid6: int32x1 61 MB/s
[ 30.550000] raid6: int32x2 82 MB/s
[ 30.720000] raid6: int32x4 83 MB/s
[ 30.890000] raid6: int32x8 76 MB/s
[ 30.890000] raid6: using algorithm int32x4 (83 MB/s)
[ 31.040000] md: raid6 personality registered for level 6
[ 31.040000] md: raid5 personality registered for level 5
[ 31.050000] md: raid4 personality registered for level 4
[ 31.130000] device-mapper: ioctl: 4.16.0-ioctl (2009-11-05) initialised: dm-devel@redhat.com
[ 31.320000] cryptodev: driver 0.9 loaded.
[ 31.410000] usbcore: registered new interface driver usbhid
[ 31.410000] usbhid: USB HID core driver
[ 31.450000] usbcore: registered new interface driver usblp
[ 31.490000] sysinfo: Module loaded.
[ 31.670000] fnotify: module license 'non-GPL' taints kernel.
[ 31.680000] Disabling lock debugging due to kernel taint
[ 31.720000] fnotify: Load file notify kernel module.
[ 31.730000] fnotify: Global_Private_Data_List_Init()
[ 31.730000] fnotify: Launch the fnotify thread: 710
[ 31.740000] fnotify: The fnotify thread starts...
[ 31.800000] Enable WDT...
[ 34.060000] eth0: mac address changed
[ 34.090000] eth0: link down
[ 34.100000] eth0: started
MAC_ADDR 00:08:9B:BF:F8:22
mount: /dev/sda1 is not a valid block device
log hidden config directory not exist, initial log file...
Initialize database...
Done. Return value is 0
Set max number of logs to 50
Done. Return value is 0
Initialize database...
Done. Return value is 0
Set max number of logs to 50
Done. Return value is 0
[ 35.740000] eth0: link up, full duplex, speed 100 Mbps
NIC 1 Link is Up
init_netlink_socket error!
storage_boot_init 3 ...
storage_boot_init.c: booting without HD
storage_boot_init 4 ...
storage_boot_init.c: Set Status LED...
[/sys/block/sda]
[ 39.830000] eth0: stopped
eth0 DHCP
[ 41.030000] eth0: link down
[ 41.030000] eth0: started
[ 44.220000] eth0: link up, full duplex, speed 100 Mbps
sh: /sbin/lcd_tool: No such file or directory
default: 0xa2
upnpd[1318]: UPnP SDK Successfully Initialized.
upnpd[1318]: Succesfully set the Web Server Root Directory.
upnpd[1318]: IGD root device successfully registered.
sh: /sbin/lcd_tool: No such file or directory
NASBFF822
killall: snmpd: no process killed
Stopping network...
Shutting down upnpd services:1317 1318
.
[ 67.430000] eth0: stopped
/etc/rcS.d/S45network: line 580: /etc/init.d/vlan.sh: No such file or directory
Stopped.
Starting network...eth0 DHCP
[ 69.320000] eth0: link down
[ 69.330000] eth0: started
[ 70.940000] eth0: link up, full duplex, speed 100 Mbps
Shutting down winbindd services:Shutting down upnpd services:killall: upnpcd: no process killed
winbindd.
killall: snmpd: no process killed
Starting winbindd services:1317 1318
.
Starting upnpd: get eth0 gateway = 192.168.81.1
sh: /usr/bin/qcmd: No such file or directory
upnpd[1946]: UPnP SDK Successfully Initialized.
upnpd[1946]: Succesfully set the Web Server Root Directory.
upnpd[1946]: IGD root device successfully registered.
default via 192.168.81.1 dev eth0
.
upnpd[1946]: Advertisements Sent. Listening for requests ...
[ 87.990000] eth0: stopped
[ 88.020000] eth0: link down
[ 88.020000] eth0: started
Starting thttpd services:[ 89.660000] eth0: link up, full duplex, speed 100 Mbps
thttpd.
Starting Qthttpd services:Default share Web is not found. Apache httpd start failed.
config_util: No initialized HD exists.
init_check.sh: No HD existed.
Starting sshd services: sshd.
Starting telnet services: disabled.
Starting opentftpd services: disabled.
Starting stunnel services: /bin/cp: cannot create regular file `/etc/config/stunnel/backup.cert': No such file or directory
/bin/cp: cannot create regular file `/etc/config/stunnel/backup.key': No such file or directory
stunnel.
Shutting down bonjour services:cat: /var/lock/bonjour.normal: No such file or directory
mDNSResponderPosix
Starting bonjour services: mDNSResponderPosix.
1317 1318 1945 1946
[ 100.590000] warning: process `pic_raw' used the deprecated sysctl system call with 8.1.2.
sed: /home/httpd/cgi-bin/Qrecordings/help/*.html: No such file or directory
sed: /home/httpd/help/inc/app/*.js: No such file or directory
sed: /home/httpd/cgi-bin/inc/*.js: No such file or directory
sed: /home/httpd/cgi-bin/inc/*.js: No such file or directory
/etc/init.d/genLanglist.sh: line 46: /home/httpd/ajax_obj/extjs/languages.js: No such file or directory
/etc/init.d/genLanglist.sh: line 47: /home/httpd/ajax_obj/extjs/languages.js: No such file or directory
sss_convert...[pass]
killall: snmpd: no process killed
/etc/init.d/usb_device_check.sh: line 25: /usr/sbin/lsusb: No such file or directory
Welcome to TS-110(192.168.81.95), QNAP Systems, Inc.
NASBFF822 login:
TS-110のブートメッセージ
つないだ。
VCCをつなぐと暴走(?)して、パワースイッチで起動しなかったり、
RXとTXをつながないで、RX-RX、TX-TXとしてしまってはまったりしたが、
無事にブートメッセージ(dmesgなど)を見ることができた。
使った部品は以下の通り、
USB-RS-232C変換器
FTDI TTL-232R-3V3
http://akizukidenshi.com/catalog/g/gM-05840/
http://www.ftdichip.com/Products/Cables/USBTTLSerial.htm
ブレッドボード
EIC-310
http://akizukidenshi.com/catalog/g/gP-00313/
ピンヘッダー (2.54mmピッチ)
http://akizukidenshi.com/catalog/g/gC-00167/
JST PHR-4用端子
http://www.aitendo.com/product/3381
ピンヘッダーは、TTL-232R-3V3とブレッドボードをつなぐのに使う。
JST PHR-4用端子のケーブル側は、ちょっと細いがブレッドボードに
ささるので、そのまま挿す。
実際の接続は、
http://www.cyrius.com/debian/kirkwood/qnap/ts-119/serial.html
にある通り、前面側からGND、RX、VCC、TXの順なので、
GNDをTTL-232R-3V3の黒(GND)に、
RXをTTL-232R-3V3の橙(TXD)に、
VCCはつながずに、
TXをTTL-232R-3V3の黄(RXD)に、
それぞれつなぐ。
カメラを忘れてしまったので、写真は取っていない。
追記(2013-03-10)
配線までは分からないだろうが、現状の接続状況の写真を撮ったので掲示しておく。
console側のNetBSDマシンでは、
# screen /dev/ttyU0 115200
として、待っている状態で、電源を入れると、以下のような
ブートメッセージが得られる。
MACアドレスはCC:CC:CC:CC:CC:CCに置き換えてある。
まあ、ここまでではCPUが分かったくらいの収穫。
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-88F6281A-BP LE
U-Boot 1.1.4 (Apr 23 2009 - 19:01:28) Marvell version: 3.4.4
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690DCC
Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
[16384kB@f8000000] Flash: 16 MB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Unknown command 'uart1' - try 'help'
## Booting image at 00800000 ...
Image Name: Linux-2.6.33.2
Created: 2012-12-05 7:14:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2083192 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux................................................................................................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.33.2 (root@VMBuildEnv001) (gcc version 4.2.1) #1 Wed Dec 5 15:14:47 CST 2012
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Feroceon-KW ARM
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/ram initrd=0xa00000,0x900000 ramdisk=32768
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 246016KB available (3784K code, 451K data, 136K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[ 0.230000] Mount-cache hash table entries: 512
[ 0.230000] CPU: Testing write buffer coherency: ok
[ 0.230000] NET: Registered protocol family 16
[ 0.230000] Feroceon L2: Enabling L2
[ 0.230000] Feroceon L2: Cache support initialised.
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e0000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] PEX1_MEM ....no such
[ 0.260000] PEX1_IO ....no such
[ 0.260000] INTER_REGS ....base f1000000, size 1MB
[ 0.260000] NFLASH_CS ....base fa000000, size 2MB
[ 0.260000] SPI_CS ....base f4000000, size 16MB
[ 0.260000] BOOT_ROM_CS ....no such
[ 0.260000] DEV_BOOTCS ....no such
[ 0.260000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.260000]
[ 0.260000] Marvell Development Board (LSP Version KW_LSP_5.1.2)-- DB-88F6281A-BP Soc: 88F6281 A1 LE
[ 0.260000]
[ 0.260000] Detected Tclk 200000000 and SysClk 400000000
[ 0.260000] MV Buttons Device Load
[ 3.280000] PEX0 interface detected no Link.
[ 3.280000] PCI: bus0: Fast back to back transfers enabled
[ 3.280000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[ 3.290000] bio: create slab <bio-0> at 0
[ 3.290000] vgaarb: loaded
[ 3.290000] SCSI subsystem initialized
[ 3.290000] usbcore: registered new interface driver usbfs
[ 3.290000] usbcore: registered new interface driver hub
[ 3.290000] usbcore: registered new interface driver ethub
[ 3.290000] usbcore: registered new device driver usb
[ 3.290000] Switching to clocksource kw_clocksource
[ 3.290000] NET: Registered protocol family 2
[ 3.290000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 3.290000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 3.290000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 3.290000] TCP: Hash tables configured (established 8192 bind 8192)
[ 3.290000] TCP reno registered
[ 3.290000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 3.290000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 3.290000] NET: Registered protocol family 1
[ 3.290000] RPC: Registered udp transport module.
[ 3.290000] RPC: Registered tcp transport module.
[ 3.290000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 3.290000] Trying to unpack rootfs image as initramfs...
[ 3.290000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 3.340000] Freeing initrd memory: 9216K
[ 3.340000] QNAP RTC initializing....
[ 3.380000] Initializing RTC is completed.
[ 3.400000] rtc kw_rtc: rtc core: registered kw-rtc as rtc0
[ 3.400000] RTC registered
[ 3.400000] watchdog_init: succeed to register misc device
[ 3.400000] Init WDT and Active SYSREST if WDT timeout
[ 3.400000] XOR registered 4 channels
[ 3.400000] XOR 2nd invalidate WA enabled
[ 3.400000] MV Buttons Driver Load
[ 3.400000] NetWinder Floating Point Emulator V0.97 (double precision)
[ 3.400000] audit: initializing netlink socket (disabled)
[ 3.400000] type=2000 audit(1362625395.000:1): initialized
[ 3.400000] VFS: Disk quotas dquot_6.5.2
[ 3.400000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.410000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 3.410000] fuse init (API version 7.13)
[ 3.410000] msgmni has been set to 499
[ 3.410000] alg: No test for stdrng (krng)
[ 3.410000] io scheduler noop registered
[ 3.410000] io scheduler deadline registered
[ 3.410000] io scheduler cfq registered (default)
[ 3.430000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.430000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 3.440000] console [ttyS0] enabled
[ 3.450000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 3.460000] brd: module loaded
[ 3.460000] loop: module loaded
[ 3.470000] qnap_pic_init: succeed to register misc device
[ 3.470000] tsinfo: create proc systemp successfully
[ 3.480000] tsinfo: create proc systemp successfully
[ 3.480000] tsinfo: create proc systemp successfully
[ 3.490000] tsinfo: create proc systemp successfully
[ 3.490000] serial8250_PIC_init..uartclk = 200000000,baudDivisor = 651,irq = 34
[ 3.500000] Integrated Sata device found
[ 3.510000] IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
[ 5.550000] Spin up ...(0:0)
[ 7.560000] Spin up ...(0:1)
[ 9.560000] Spin up all...
[ 12.560000] [0 0]: Waiting for channel initialization.
[ 13.570000] [0 1]: Waiting for channel initialization.
[ 14.570000] scsi0 : Marvell SCSI to SATA adapter
[ 14.580000] scsi1 : Marvell SCSI to SATA adapter
[ 15.080000] ENABLE_WRITE_CACHE (current: enabled).
[ 15.090000] scsi 0:0:0:0: Direct-Access WDC WD20EARS-00MVWB0 51.0 PQ: 0 ANSI: 5
[ 15.100000] Check proc_name[mvSata].
[ 15.100000] Check proc_name[mvSata].
[ 15.110000] sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
[ 15.110000] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 15.120000] sd 0:0:0:0: [sda] 0-byte physical blocks
[ 15.130000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 15.130000] SPI Serial flash detected @ 0xf4000000, 16384KB (64sec x 256KB)
[ 15.140000] Creating 6 MTD partitions on "spi_flash":
[ 15.150000] 0x000000000000-0x000000080000 : "U-Boot"
[ 15.150000] 0x000000200000-0x000000400000 : "Kernel"
[ 15.160000] sd 0:0:0:0: [sda] Write Protect is off
[ 15.160000] 0x000000400000-0x000000d00000 : "RootFS"
[ 15.170000] 0x000000d00000-0x000001000000 : "RootFS2"
[ 15.170000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 15.180000] 0x000000080000-0x0000000c0000 : "U-Boot Config"
[ 15.190000] sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
[ 15.200000] 0x0000000c0000-0x000000200000 : "NAS Config"
[ 15.200000] Loading Marvell Ethernet Driver:
[ 15.210000] o Cached descriptors in DRAM
[ 15.210000] o DRAM SW cache-coherency
[ 15.210000] o 1 Giga ports supported
[ 15.220000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 15.220000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 15.230000] o TCP segmentation offload (TSO) supported
[ 15.230000] o Large Receive offload (LRO) supported
[ 15.240000] o Receive checksum offload supported
[ 15.240000] o Transmit checksum offload supported
[ 15.250000] o Network Fast Processing (Routing) supported - (Disabled)
[ 15.260000] o Proc tool API enabled
[ 15.260000] o SKB Reuse supported - (Disabled)
[ 15.260000] o SKB Recycle supported - (Disabled)
[ 15.270000] o Rx descripors: q0=128
[ 15.270000] o Tx descripors: q0=532
[ 15.280000] o Loading network interface(s):
[ 15.280000] o register under mv88fx_eth platform
[ 15.290000] o eth0, ifindex = 2, GbE port = 0
[ 15.290000]
[ 15.300000] mvFpRuleDb (00000010): 0 entries, 0 bytes
[ 15.300000] Marvell debug tracing is on
[ 15.300000] Initializing USB Mass Storage driver...
[ 15.310000] usbcore: registered new interface driver usb-storage
[ 15.320000] USB Mass Storage support registered.
[ 15.320000] usb: create proc systemp successfully
[ 15.330000] usb: create proc systemp successfully
[ 15.330000] mice: PS/2 mouse device common for all mice
[ 15.340000] md: linear personality registered for level -1
[ 15.340000] md: raid0 personality registered for level 0
[ 15.350000] md: raid1 personality registered for level 1
[ 15.350000] TCP cubic registered
[ 15.350000] NET: Registered protocol family 17
[ 15.360000] sda:
[ 15.380000] rtc kw_rtc: setting system clock to 2013-03-07 03:03:28 UTC (1362625408)
[ 15.760000] sda1 sda2 sda3 sda4
[ 15.780000] sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
[ 15.800000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 15.800000] md: Waiting for all devices to be available before autodetect
[ 15.810000] md: If you don't use raid, use raid=noautodetect
[ 15.820000] md: Autodetecting RAID arrays.
[ 15.820000] md: Scanned 0 and added 0 devices.
[ 15.820000] md: autorun ...
[ 15.830000] md: ... autorun DONE.
[ 15.830000] RAMDISK: gzip image found at block 0
[ 17.160000] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 17.160000] Freeing init memory: 136K
[ 17.620000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.630000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 17.630000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 17.670000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 17.690000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 17.690000] hub 1-0:1.0: USB hub found
[ 17.700000] hub 1-0:1.0: 1 port detected
Start config_util...
[ 18.020000] usb 1-1: new high speed USB device using orion-ehci and address 2
Start to mirror ROOT part...
[ 18.110000] kjournald starting. Commit interval 5 seconds
[ 18.120000] EXT3-fs (sda1): mounted filesystem with writeback data mode
[ 18.170000] hub 1-1:1.0: USB hub found
[ 18.170000] hub 1-1:1.0: 4 ports detected
config_util: HD1 config Match serial_no of HD1.
[ 18.470000] md: md9 stopped.
[ 18.480000] md: bind<sda1>
[ 18.510000] raid1: raid set md9 active with 1 out of 1 mirrors
[ 18.530000] md9: bitmap initialized from disk: read 5/5 pages, set 0 bits
[ 18.540000] created bitmap (65 pages) for device md9
[ 18.570000] md9: detected capacity change from 0 to 542769152
mdadm: /dev/md9 has been started with 1 drive.
[ 18.600000] md9: unknown partition table
mdadm: '1' is an unusual number of drives for an array, so it is probably
a mistake. If you really mean it you will need to specify --force before
setting the number of drives.
Mirror of ROOT succeeded.
[ 19.980000] kjournald starting. Commit interval 5 seconds
[ 19.990000] EXT3-fs (md9): using internal journal
[ 19.990000] EXT3-fs (md9): mounted filesystem with writeback data mode
Start to mirror RFS_EXT part...
config_util: HD1 is TS-NASARM.
[ 20.250000] md: md13 stopped.
[ 20.280000] md: bind<sda4>
[ 20.290000] raid1: raid set md13 active with 1 out of 1 mirrors
[ 20.310000] md13: bitmap initialized from disk: read 4/4 pages, set 0 bits
[ 20.320000] created bitmap (57 pages) for device md13
[ 20.330000] md13: detected capacity change from 0 to 469893120
mdadm: /dev/sda4 has been started with 1 drive.
[ 20.350000] md13: unknown partition table
mdadm: '1' is an unusual number of drives for an array, so it is probably
a mistake. If you really mean it you will need to specify --force before
setting the number of drives.
config_util: (0) /dev/sda4 size = 458880
Mirror of RFS_EXT succeeded.
config_util finished.
mount HDD root device
[ 21.220000] kjournald starting. Commit interval 5 seconds
[ 21.290000] EXT3-fs (md9): using internal journal
[ 21.290000] EXT3-fs (md9): mounted filesystem with writeback data mode
mount /dev/md9 successful.
bootcmd check ok
Update Extended rcX_init.d...(1)
4+0 records in
4+0 records out
Extract RootFS Ext...
[ 21.770000] kjournald starting. Commit interval 5 seconds
[ 21.830000] EXT3-fs (md9): using internal journal
[ 21.830000] EXT3-fs (md9): mounted filesystem with writeback data mode
mountall: mount /dev/md9 successful.
[ 23.600000] kjournald starting. Commit interval 5 seconds
[ 23.610000] EXT3-fs (md13): using internal journal
[ 23.610000] EXT3-fs (md13): recovery complete
[ 23.640000] EXT3-fs (md13): mounted filesystem with writeback data mode
install /hd_root_tmp/update_pkg/samba.tgz
/hd_root_tmp/update_pkg/WFM3.tgz is not exist!
/hd_root_tmp/update_pkg/WFM2.tgz is not exist!
install /hd_root_tmp/update_pkg/language.tgz
install /hd_root_tmp/update_pkg/vpnpptp.tgz!
install /hd_root_tmp/update_pkg/vaultServices.tgz
install /hd_root_tmp/update_pkg/DSv3.tgz
install /hd_root_tmp/update_pkg/vpnopenvpn.tgz!
install /hd_root_tmp/update_pkg/ldap_server.tgz!
install /hd_root_tmp/update_pkg/avahi0630.tgz!
install /hd_root_tmp/update_pkg/medialibrary.tgz
install /hd_root_tmp/update_pkg/printer.tgz
install /hd_root_tmp/update_pkg/vim.tgz
mv: unable to rename `/mnt/ext/opt/DSv3/opt/gt': Directory not empty
[ 47.800000] NET: Registered protocol family 5
[ 48.290000] TARGET_CORE[0]: Loading Generic Kernel Storage Engine: v3.5.0 on Linux/armv5tel on 2.6.33.2
[ 48.300000] TARGET_CORE[0]: Initialized ConfigFS Fabric Infrastructure: v3.5.0 on Linux/armv5tel on 2.6.33.2
[ 48.310000] SE_PC[0] - Registered Plugin Class: TRANSPORT
[ 48.310000] PLUGIN_TRANSPORT[1] - pscsi registered
[ 48.320000] PLUGIN_TRANSPORT[4] - iblock registered
[ 48.320000] PLUGIN_TRANSPORT[5] - rd_dr registered
[ 48.330000] PLUGIN_TRANSPORT[6] - rd_mcp registered
[ 48.330000] PLUGIN_TRANSPORT[7] - fileio registered
[ 48.340000] SE_PC[1] - Registered Plugin Class: OBJ
[ 48.340000] PLUGIN_OBJ[1] - dev registered
[ 48.340000] CORE_HBA[0] - Linux-iSCSI.org Ramdisk HBA Driver v3.1 on Generic Target Core Stack v3.5.0
[ 48.350000] CORE_HBA[0] - Attached Ramdisk HBA: 0 to Generic Target Core TCQ Depth: 256 MaxSectors: 1024
[ 48.360000] CORE_HBA[0] - Attached HBA to Generic Target Core
[ 48.370000] RAMDISK: Referencing Page Count: 8
[ 48.370000] CORE_RD[0] - Built Ramdisk Device ID: 0 space of 8 pages in 1 tables
[ 48.380000] rd_dr: Using SPC_PASSTHROUGH, no reservation emulation
[ 48.390000] rd_dr: Using SPC_ALUA_PASSTHROUGH, no ALUA emulation
[ 48.390000] CORE_RD[0] - Activating Device with TCQ: 0 at Ramdisk Device ID: 0
[ 48.530000] Vendor: QNAP Model: RAMDISK-DR Revision: 3.1
[ 48.530000] Type: Direct-Access ANSI SCSI revision: 05
[ 48.550000] T10 VPD Unit Serial Number: 1234567890:0_0
[ 48.550000] T10 VPD Page Length: 38
[ 48.550000] T10 VPD Identifer Length: 34
[ 48.560000] T10 VPD Identifier Association: addressed logical unit
[ 48.560000] T10 VPD Identifier Type: T10 Vendor ID based
[ 48.570000] T10 VPD ASCII Device Identifier: QNAP
[ 48.600000] CORE_RD[0] - Added LIO DIRECT Ramdisk Device ID: 0 of 8 pages in 1 tables, 32768 total bytes
[ 48.800000] Initiate iscsi target log successfully.
[ 48.800000] Linux-iSCSI.org iSCSI Target Core Stack v3.5.0 on Linux/armv5tel on 2.6.33.2
[ 48.810000] <<<<<<<<<<<<<<<<<<<<<< BEGIN FABRIC API >>>>>>>>>>>>>>>>>>>>>>
[ 48.820000] Initialized struct target_fabric_configfs: cdb67800 for iscsi
[ 48.820000] <<<<<<<<<<<<<<<<<<<<<< END FABRIC API >>>>>>>>>>>>>>>>>>>>>>
[ 48.830000] LIO_TARGET[0] - Set fabric -> lio_target_fabric_configfs
[ 48.910000] iscsi_allocate_thread_sets:206: ***OPS*** Spawned 4 thread set(s) (8 total threads).
[ 48.910000] TARGET_CORE[iSCSI]: Allocated Discovery se_portal_group_t for endpoint: None, Portal Tag: 1
[ 48.920000] CORE[0] - Allocated Discovery TPG
[ 48.930000] Loading Complete.
[ 48.960000] xor: measuring software checksum speed
[ 49.010000] arm4regs : 726.000 MB/sec
[ 49.060000] 8regs : 550.800 MB/sec
[ 49.110000] 32regs : 608.400 MB/sec
[ 49.110000] xor: using function: arm4regs (726.000 MB/sec)
[ 49.650000] raid6: int32x1 61 MB/s
[ 49.820000] raid6: int32x2 82 MB/s
[ 49.990000] raid6: int32x4 83 MB/s
[ 50.160000] raid6: int32x8 77 MB/s
[ 50.160000] raid6: using algorithm int32x4 (83 MB/s)
[ 51.140000] md: raid6 personality registered for level 6
[ 51.140000] md: raid5 personality registered for level 5
[ 51.150000] md: raid4 personality registered for level 4
[ 51.250000] device-mapper: ioctl: 4.16.0-ioctl (2009-11-05) initialised: dm-devel@redhat.com
[ 51.650000] cryptodev: driver 0.9 loaded.
[ 51.870000] usbcore: registered new interface driver usbhid
[ 51.870000] usbhid: USB HID core driver
[ 51.950000] usbcore: registered new interface driver usblp
[ 51.980000] sysinfo: Module loaded.
[ 52.390000] ufsd: module license 'Commercial product' taints kernel.
[ 52.390000] Disabling lock debugging due to kernel taint
[ 52.510000] ufsd: driver (8.6, Dec 5 2012 15:49:21, LBD=ON, delalloc, acl, ioctl, ugm) loaded at bf266000
[ 52.510000] NTFS (with native replay) support included
[ 52.510000] Hfs+/HfsX support included
[ 52.510000] optimized: speed
[ 52.510000] Build_for__QNAP_TS_219_ARM_2012-02-09_U86_r184991_b10
[ 52.510000]
[ 53.010000] Slow work thread pool: Starting up
[ 53.010000] Slow work thread pool: Ready
[ 53.170000] fnotify: Load file notify kernel module.
[ 53.180000] fnotify: Global_Private_Data_List_Init()
[ 53.180000] fnotify: Launch the fnotify thread: 1090
[ 53.190000] fnotify: The fnotify thread starts...
[ 53.250000] lib80211: common routines for IEEE802.11 drivers
[ 53.430000] cfg80211: Calling CRDA to update world regulatory domain
[ 53.780000] Enable WDT...
[ 55.950000] usbcore: registered new interface driver snd-usb-audio
[ 55.980000] usbcore: registered new interface driver snd-usb-caiaq
[ 56.090000] Linux video capture interface: v2.00
[ 56.170000] usbcore: registered new interface driver uvcvideo
[ 56.180000] USB Video Class driver (v0.1.0)
[ 57.380000] eth0: mac address changed
[ 57.420000] eth0: link down
[ 57.420000] eth0: started
MAC_ADDR CC:CC:CC:CC:CC
[ 59.010000] eth0: link up, full duplex, speed 100 Mbps
storage_boot_init 1 ...
[ 72.870000] kjournald starting. Commit interval 5 seconds
[ 72.890000] EXT3-fs (md9): using internal journal
[ 72.890000] EXT3-fs (md9): mounted filesystem with writeback data mode
readlink: /etc/config: Invalid argument
config hidden config directory exist, create symbolic link /etc/config... [OK]
Writing model version information...
Writing model version info...[OK]
ln: /home/httpd/cgi-bin/loginTheme/theme: No such file or directory
ln: /home/httpd/cgi-bin/loginTheme/theme/desktop.jpg: No such file or directory
sss_convert...
log hidden config directory exist, create symboloc link /etc/logs... [OK]
Install /mnt/HDA_ROOT/update_pkg/*.qfix ...
Start rcv_port: [ 75.990000] active port 0 :139
[ 75.990000] active port 1 :445
[ 75.990000] active port 2 :20
set 139 445 20.
/sbin/modagent start
init_netlink_socket error!
Starting Disk initialized:
Check config files...start
No need to do recovery.
storage_boot_init 2 ...
mdadm: No md superblock detected on /dev/sda3.
storage_boot_init.c: Check filesystem on /dev/sda3.
mdadm: /dev/sda2 appears to be part of a raid array:
level=raid1 devices=2 ctime=Thu Mar 7 02:54:59 2013
[ 84.320000] md: bind<sda2>
[ 84.330000] raid1: raid set md1 active with 1 out of 1 mirrors
[ 84.340000] md1: detected capacity change from 0 to 542769152
mdadm: array /dev/md1 started.
[ 85.370000] md1: unknown partition table
[ 87.470000] Adding 530040k swap on /dev/md1. Priority:-1 extents:1 across:530040k
[ 95.030000] EXT4-fs (sda3): mounted filesystem with ordered data mode
storage_boot_init.c: check_last_degrade_error...
group block bitmap usage checking...
find default mount path /share/HDA_DATA
storage_boot_init 6 ...
storage_boot_init.c: Checking e-sata: [/sys/block/sdz]
Not exist
/dev/sda3 on /share/HDA_DATA type ext4 (rw,usrjquota=aquota.user,jqfmt=vfsv0,user_xattr,data=ordered,delalloc,noacl)
crontab: cannot change dir to /tmp/cron/crontabs: No such file or directory
crontab: cannot change dir to /tmp/cron/crontabs: No such file or directory
crontab: cannot change dir to /tmp/cron/crontabs: No such file or directory
Restarting nmbd services:killall: snmpd: no process killed
Stopping network...
nmbd.
done.
Shutting down upnpd services:sh: /usr/bin/qcmd: No such file or directory
.
[ 110.320000] eth0: stopped
/etc/init.d/network.sh: line 580: /etc/init.d/vlan.sh: No such file or directory
Stopped.
Starting network...eth0 STATIC
[ 112.260000] eth0: link down
[ 112.260000] eth0: started
[ 114.080000] eth0: link up, full duplex, speed 100 Mbps
Shutting down winbindd services:192.168.81.1
killall: upnpcd: no process killed
winbindd.
Shutting down upnpd services:Restarting nmbd services:killall: snmpd: no process killed
Starting winbindd services: nmbd.
done.
.
Starting upnpd: get eth0 gateway = 192.168.81.1
default via 192.168.81.1 dev eth0 metric 1
upnpd[2372]: UPnP SDK Successfully Initialized.
upnpd[2372]: Succesfully set the Web Server Root Directory.
upnpd[2372]: IGD root device successfully registered.
[ 131.520000] eth0: stopped
[ 131.550000] eth0: link down
[ 131.550000] eth0: started
.
upnpd[2372]: Advertisements Sent. Listening for requests ...
[ 133.180000] eth0: link up, full duplex, speed 100 Mbps
rpcbind: cannot create socket for udp6
rpcbind: cannot create socket for tcp6
[ 141.400000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 141.410000] NFSD: starting 90-second grace period
Initializing random number generator... done.
Install /mnt/HDA_ROOT/update_pkg/*.qpkg ...
Starting ldap services:Starting thttpd services: disabled.
Starting wfm_thttpd services: no enable defined port.
thttpd.
Starting Qthttpd services:locks path was set to /share/HDA_DATA/.locks
Qthttpd.
Starting winbindd services:Starting SMB services: smbd nmbd.
Startup all cloud related services...
Starting FTP services: Start rcv_port: [ 157.920000] active port 0 :139
[ 157.920000] active port 1 :445
[ 157.920000] active port 2 :20
Starting stunnel services: /mnt/ext/opt/mysql
set 139 445 20.
insmod: cannot insert `/lib/modules/misc/fbdisk.ko': File exists (-1): File exists
Starting UPS monitoring:Shutting down NFS daemon: rpc.nfsdStarting NTP services: /bin/mknod: `/dev/fbdisk0': File exists
/bin/mknod: `/dev/fbsnap0': File exists
The vaultServices is disabled...
/bin/mknod: `/dev/fbdisk1': File exists
/bin/mknod: `/dev/fbsnap1': File exists
Starting recycled services:/bin/mknod: `/dev/fbdisk2': File exists
Remove old configuration files
/bin/mknod: `/dev/fbsnap2': File exists
/bin/mknod: `/dev/fbdisk3': File exists
yes
/bin/mknod: `/dev/fbsnap3': File exists
/bin/mknod: `/dev/fbdisk4': File exists
/bin/mknod: `/dev/fbsnap4': File exists
Try to shutting down AVAHI services first
Starting DS scheduler: Starting QSync manitor: qsyncman...
/bin/mknod: `/dev/fbdisk5': File exists
/bin/mknod: `/dev/fbsnap5': File exists
/bin/mknod: `/dev/fbdisk6': File exists
/bin/mknod: `/dev/fbsnap6': File exists
/bin/mknod: `/dev/fbdisk7': File exists
/bin/mknod: `/dev/fbsnap7': File exists
Network UPS Tools - UPS driver controller 2.2.2
/bin/mknod: `/dev/fbdisk8': File exists
/bin/mknod: `/dev/fbsnap8': File exists
/bin/mknod: `/dev/fbdisk9': File exists
/bin/mknod: `/dev/fbsnap9': File exists
Network UPS Tools: 0.29 USB communication driver - core 0.33 (2.2.2)
proftpd.
No matching HID UPS found
Driver failed to start (exit status=1)
/bin/mknod: `/dev/fbdisk10': File exists
/bin/mknod: `/dev/fbsnap10': File exists
/bin/mknod: `/dev/fbdisk11': File exists
/bin/mknod: `/dev/fbsnap11': File exists
/bin/mknod: `/dev/fbdisk12': File exists
/bin/mknod: `/dev/fbsnap12': File exists
Starting periodic command scheduler: Starting sshd services: Network UPS Tools upsd 2.2.2
/etc/init.d/refresh_nvr_crontab.sh: line 16: /usr/bin/qcmd: No such file or directory
/bin/mknod: `/dev/fbdisk13': File exists
/bin/mknod: `/dev/fbsnap13': File exists
ntpdated.
/bin/mknod: `/dev/fbdisk14': File exists
Enable Optware/ipkg
/bin/mknod: `/dev/fbsnap14': File exists
/bin/mknod: `/dev/fbdisk15': File exists
/bin/mknod: `/dev/fbsnap15': File exists
/bin/mknod: `/dev/fbdisk16': File exists
/bin/mknod: `/dev/fbsnap16': File exists
Reconfigure FTP services:
/bin/mknod: `/dev/fbdisk17': File exists
Starting media stations: [ 165.690000] warning: `proftpd' uses 32-bit capabilities (legacy support in use)
/bin/cp: `/mnt/ext/opt/photostation2/geoip.xml' and `/tmp/geoip.xml' are the same file
/bin/mknod: `/dev/fbsnap17': File exists
/bin/mknod: `/dev/fbdisk18': File exists
crond[3497]: crond 2.3.2 dillon, started, log level 9
crond[3497]: failed user admin parsing [global]
crond[3497]: failed user admin parsing workgroup = elements
crond[3497]: failed user admin parsing security = USER
crond[3497]: failed user admin parsing server string = qnap NAS
crond[3497]: failed user admin parsing username level = 0
crond[3497]: failed user admin parsing null passwords = yes
crond[3497]: failed user admin parsing socket options = TCP_NODELAY SO_KEEPALIVE SO_SNDBUF=65536 SO_RCVBUF=65536
crond[3497]: failed user admin parsing os level = 20
crond[3497]: failed user admin parsing preferred master = no
/bin/mknod: `/dev/fbsnap18': File exists
Starting IM services:No MSN account information
/bin/mknod: `/dev/fbdisk19': File exists
/bin/mknod: `/dev/fbsnap19': File exists
TwonkyMedia cache have been cleaned.
/bin/mknod: `/dev/fbdisk20': File exists
/bin/mknod: `/dev/fbsnap20': File exists
/bin/mknod: `/dev/fbdisk21': File exists
/bin/mknod: `/dev/fbsnap21': File exists
[ 167.510000] nfsd: last server has exited, flushing export cache
reconfig ftp success
crond.
use PIC1 as default image
/bin/mknod: `/dev/fbdisk22': File exists
/bin/mknod: `/dev/fbsnap22': File exists
Could not load host key: /etc/ssh/ssh_host_rsa_key
/bin/mknod: `/dev/fbdisk23': File exists
/bin/mknod: `/dev/fbsnap23': File exists
Starting iTune Services: disabled.
/bin/mknod: `/dev/fbdisk24': File exists
/bin/mknod: `/dev/fbsnap24': File exists
Starting UPnP MediaServer: (/mnt/HDA_ROOT/twonkymedia/twonkymedia) /bin/mknod: `/dev/fbdisk25': File exists
/bin/mknod: `/dev/fbsnap25': File exists
/bin/mknod: `/dev/fbdisk26': File exists
sshd.
/bin/mknod: `/dev/fbsnap26': File exists
/bin/mknod: `/dev/fbdisk27': File exists
/bin/mknod: `/dev/fbsnap27': File exists
/bin/mknod: `/dev/fbdisk28': File exists
/bin/mknod: `/dev/fbsnap28': File exists
/bin/mknod: `/dev/fbdisk29': File exists
/bin/mknod: `/dev/fbsnap29': File exists
/bin/mknod: `/dev/fbdisk30': File exists
sss_convert...
/bin/mknod: `/dev/fbsnap30': File exists
/bin/mknod: `/dev/fbdisk31': File exists
/bin/mknod: `/dev/fbsnap31': File exists
/bin/mknod: `/dev/fbdisk32': File exists
/bin/mknod: `/dev/fbsnap32': File exists
Network UPS Tools - UPS driver controller 2.2.2
Network UPS Tools: 0.29 USB communication driver - core 0.33 (2.2.2)
/bin/mknod: `/dev/fbdisk33': File exists
.
Shutting down NFS mountd: rpc.mountdNo matching HID UPS found
Driver failed to start (exit status=1)
/bin/mknod: `/dev/fbsnap33': File exists
/bin/mknod: `/dev/fbdisk34': File exists
install /mnt/HDA_ROOT/update_pkg/DSv3.tgz
/bin/mknod: `/dev/fbsnap34': File exists
disabled
/bin/mknod: `/dev/fbdisk35': File exists
/bin/mknod: `/dev/fbsnap35': File exists
/bin/mknod: `/dev/fbdisk36': File exists
/bin/mknod: `/dev/fbsnap36': File exists
/bin/mknod: `/dev/fbdisk37': File exists
/bin/mknod: `/dev/fbsnap37': File exists
/bin/mknod: `/dev/fbdisk38': File exists
/bin/mknod: `/dev/fbsnap38': File exists
Starting telnet services: disabled.
/bin/mknod: `/dev/fbdisk39': File exists
/bin/mknod: `/dev/fbsnap39': File exists
Starting Dbus ... /bin/mknod: `/dev/fbdisk40': File exists
disabled
/bin/mknod: `/dev/fbsnap40': File exists
/bin/mknod: `/dev/fbdisk41': File exists
/bin/mknod: `/dev/fbsnap41': File exists
Starting AppleTalk services: /bin/mknod: `/dev/fbdisk42': File exists
/bin/mknod: `/dev/fbsnap42': File exists
/bin/mknod: `/dev/fbdisk43': File exists
/bin/mknod: `/dev/fbsnap43': File exists
/bin/mknod: `/dev/fbdisk44': File exists
Starting opentftpd services: disabled.
/bin/mknod: `/dev/fbsnap44': File exists
/bin/mknod: `/dev/fbdisk45': File exists
/bin/mknod: `/dev/fbsnap45': File exists
/bin/mknod: `/dev/fbdisk46': File exists
.
Shutting down NFS quotas: rpc.rquotad/bin/mknod: `/dev/fbsnap46': File exists
/bin/mknod: `/dev/fbdisk47': File exists
/bin/mknod: `/dev/fbsnap47': File exists
/bin/mknod: `/dev/fbdisk48': File exists
/bin/mknod: `/dev/fbsnap48': File exists
/bin/mknod: `/dev/fbdisk49': File exists
/bin/mknod: `/dev/fbsnap49': File exists
/bin/mknod: `/dev/fbdisk50': File exists
/bin/mknod: `/dev/fbsnap50': File exists
/bin/mknod: `/dev/fbdisk51': File exists
Dbus Started
/bin/mknod: `/dev/fbsnap51': File exists
/bin/mknod: `/dev/fbdisk52': File exists
/bin/mknod: `/dev/fbsnap52': File exists
/bin/mknod: `/dev/fbdisk53': File exists
/bin/mknod: `/dev/fbsnap53': File exists
/bin/mknod: `/dev/fbdisk54': File exists
/bin/mknod: `/dev/fbsnap54': File exists
/bin/mknod: `/dev/fbdisk55': File exists
/bin/mknod: `/dev/fbsnap55': File exists
/bin/mknod: `/dev/fbdisk56': File exists
/bin/mknod: `/dev/fbsnap56': File exists
[ 177.050000] VFS (sda3): Writes happened before quota was turned on thus quota information is probably inconsistent. Please run quotacheck(8).
/bin/mknod: `/dev/fbdisk57': File exists
stunnel.
/bin/mknod: `/dev/fbsnap57': File exists
/bin/mknod: `/dev/fbdisk58': File exists
/bin/mknod: `/dev/fbsnap58': File exists
/bin/mknod: `/dev/fbdisk59': File exists
/bin/mknod: `/dev/fbsnap59': File exists
/bin/mknod: `/dev/fbdisk60': File exists
/bin/mknod: `/dev/fbsnap60': File exists
/bin/mknod: Automatically start autorun.sh: Not found.
`/dev/fbdisk61': File exists
/bin/mknod: `/dev/fbsnap61': File exists
Starting rsync services: rsync.
rsyslogd is not Enabled.
/bin/mknod: `/dev/fbdisk62': File exists
/bin/mknod: `/dev/fbsnap62': File exists
.
/bin/mknod: `/dev/fbdisk63': File exists
/bin/mknod: `/dev/fbsnap63': File exists
Stopping portmap/bin/mknod: `/dev/fbdisk64': File exists
/bin/mknod: `/dev/fbsnap64': File exists
/bin/mknod: `/dev/fbdisk65': File exists
/bin/mknod: `/dev/fbsnap65': File exists
/bin/mknod: `/dev/fbdisk66': File exists
/bin/mknod: `/dev/fbsnap66': File exists
/bin/mknod: `/dev/fbdisk67': File exists
/bin/mknod: `/dev/fbsnap67': File exists
/bin/mknod: `/dev/fbdisk68': File exists
/bin/mknod: `/dev/fbsnap68': File exists
/bin/mknod: `/dev/fbdisk69': File exists
.
/bin/mknod: `/dev/fbsnap69': File exists
/bin/mknod: `/dev/fbdisk70': File exists
/bin/mknod: `/dev/fbsnap70': File exists
/bin/mknod: `/dev/fbdisk71': File exists
/bin/mknod: `/dev/fbsnap71': File exists
/bin/mknod: `/dev/fbdisk72': File exists
/bin/mknod: `/dev/fbsnap72': File exists
/bin/mknod: `/dev/fbdisk73': File exists
/bin/mknod: `/dev/fbsnap73': File exists
/bin/mknod: `/dev/fbdisk74': File exists
/bin/mknod: `/dev/fbsnap74': File exists
/bin/mknod: `/dev/fbdisk75': File exists
/bin/mknod: `/dev/fbsnap75': File exists
/bin/mknod: `/dev/fbdisk76': File exists
/bin/mknod: `/dev/fbsnap76': File exists
/bin/mknod: `/dev/fbdisk77': File exists
/bin/mknod: `/dev/fbsnap77': File exists
Starting NFS services: /bin/mknod: `/dev/fbdisk78': File exists
/bin/mknod: `/dev/fbsnap78': File exists
/bin/mknod: `/dev/fbdisk79': File exists
/bin/mknod: `/dev/fbsnap79': File exists
/bin/mknod: `/dev/fbdisk80': File exists
/bin/mknod: `/dev/fbsnap80': File exists
/bin/mknod: `/dev/fbdisk81': File exists
/bin/mknod: `/dev/fbsnap81': File exists
/bin/mknod: `/dev/fbdisk82': File exists
/bin/mknod: `/dev/fbsnap82': File exists
/bin/mknod: `/dev/fbdisk83': File exists
/bin/mknod: `/dev/fbsnap83': File exists
/bin/mknod: `/dev/fbdisk84': File exists
/bin/mknod: `/dev/fbsnap84': File exists
Starting portmapper:/bin/mknod: `/dev/fbdisk85': File exists
/bin/mknod: `/dev/fbsnap85': File exists
/bin/mknod: `/dev/fbdisk86': File exists
/bin/mknod: `/dev/fbsnap86': File exists
rpcbind: cannot create socket for udp6
rpcbind: cannot create socket for tcp6
.
/bin/mknod: `/dev/fbdisk87': File exists
/bin/mknod: `/dev/fbsnap87': File exists
/bin/mknod: `/dev/fbdisk88': File exists
/bin/mknod: `/dev/fbsnap88': File exists
/bin/mknod: `/dev/fbdisk89': File exists
/bin/mknod: `/dev/fbsnap89': File exists
/bin/mknod: `/dev/fbdisk90': File exists
/bin/mknod: `/dev/fbsnap90': File exists
/bin/mknod: `/dev/fbdisk91': File exists
/bin/mknod: `/dev/fbsnap91': File exists
/bin/mknod: `/dev/fbdisk92': File exists
/bin/mknod: `/dev/fbsnap92': File exists
/bin/mknod: `/dev/fbdisk93': File exists
/bin/mknod: `/dev/fbsnap93': File exists
/bin/mknod: `/dev/fbdisk94': File exists
/bin/mknod: `/dev/fbsnap94': File exists
/bin/mknod: `/dev/fbdisk95': File exists
/bin/mknod: `/dev/fbsnap95': File exists
/bin/mknod: `/dev/fbdisk96': File exists
/bin/mknod: `/dev/fbsnap96': File exists
/bin/mknod: `/dev/fbdisk97': File exists
/bin/mknod: `/dev/fbsnap97': File exists
/bin/mknod: `/dev/fbdisk98': File exists
/bin/mknod: `/dev/fbsnap98': File exists
/bin/mknod: `/dev/fbdisk99': File exists
/bin/mknod: `/dev/fbsnap99': File exists
/bin/mknod: `/dev/fbdisk100': File exists
/bin/mknod: `/dev/fbsnap100': File exists
Restarting nmbd services:/bin/mknod: `/dev/fbdisk101': File exists
/bin/mknod: `/dev/fbsnap101': File exists
/bin/mknod: `/dev/fbdisk102': File exists
/bin/mknod: `/dev/fbsnap102': File exists
/bin/mknod: `/dev/fbdisk103': File exists
/bin/mknod: `/dev/fbsnap103': File exists
/bin/mknod: `/dev/fbdisk104': File exists
/bin/mknod: `/dev/fbsnap104': File exists
/bin/mknod: `/dev/fbdisk105': File exists
/bin/mknod: `/dev/fbsnap105': File exists
/bin/mknod: `/dev/fbdisk106': File exists
/bin/mknod: `/dev/fbsnap106': File exists
/bin/mknod: `/dev/fbdisk107': File exists
/bin/mknod: `/dev/fbsnap107': File exists
killall: snmpd: no process killed
/bin/mknod: `/dev/fbdisk108': File exists
/bin/mknod: `/dev/fbsnap108': File exists
/bin/mknod: `/dev/fbdisk109': File exists
/bin/mknod: `/dev/fbsnap109': File exists
/bin/mknod: `/dev/fbdisk110': File exists
/bin/mknod: `/dev/fbsnap110': File exists
/bin/mknod: `/dev/fbdisk111': File exists
/bin/mknod: `/dev/fbsnap111': File exists
/bin/mknod: `/dev/fbdisk112're-export.
Starting NFS quotas: rpc.rquotad: File exists
/bin/mknod: `/dev/fbsnap112': File exists
/bin/mknod: `/dev/fbdisk113': File exists
/bin/mknod: `/dev/fbsnap113': File exists
/bin/mknod: `/dev/fbdisk114': File exists
/bin/mknod: `/dev/fbsnap114': File exists
/bin/mknod: `/dev/fbdisk115': File exists
/bin/mknod: `/dev/fbsnap115': File exists
/bin/mknod: `/dev/fbdisk116': File exists
/bin/mknod: `/dev/fbsnap116': File exists
/bin/mknod: `/dev/fbdisk117': File exists
/bin/mknod: `/dev/fbsnap117': File exists
/bin/mknod: `/dev/fbdisk118': File exists
/bin/mknod: `/dev/fbsnap118': File exists
/bin/mknod: `/dev/fbdisk119': File exists
/bin/mknod: `/dev/fbsnap119': File exists
/bin/mknod: `/dev/fbdisk120': File exists
/bin/mknod: `/dev/fbsnap120': File exists
/bin/mknod: `/dev/fbdisk121': File exists
/bin/mknod: `/dev/fbsnap121': File exists
/bin/mknod: `/dev/fbdisk122': File exists
/bin/mknod: `/dev/fbsnap122': File exists
/bin/mknod: `/dev/fbdisk123': File exists
/bin/mknod: `/dev/fbsnap123': File exists
.
Starting NFS mountd daemon: /bin/mknod: `/dev/fbdisk124': File exists
/bin/mknod: `/dev/fbsnap124': File exists
/bin/mknod: `/dev/fbdisk125': File exists
/bin/mknod: `/dev/fbsnap125': File exists
/bin/mknod: `/dev/fbdisk126': File exists
Shutting down NFS mountd:
/bin/mknod: `/dev/fbsnap126': File exists
/bin/mknod: `/dev/fbdisk127': File exists
/bin/mknod: `/dev/fbsnap127': File exists
/bin/mknod: `/dev/fbdisk128': File exists
/bin/mknod: `/dev/fbsnap128': File exists
/bin/mknod: `/dev/fbdisk129': File exists
/bin/mknod: `/dev/fbsnap129': File exists
/bin/mknod: `/dev/fbdisk130': File exists
/bin/mknod: `/dev/fbsnap130': File exists
/bin/mknod: `/dev/fbdisk131': File exists
/bin/mknod: `/dev/fbsnap131': File exists
/bin/mknod: `/dev/fbdisk132': File exists
/bin/mknod: `/dev/fbsnap132': File exists
/bin/mknod: `/dev/fbdisk133': File exists
/bin/mknod: `/dev/fbsnap133': File exists
/bin/mknod: `/dev/fbdisk134': File exists
nmbd.
done.
/bin/mknod: `/dev/fbsnap134': File exists
/bin/mknod: `/dev/fbdisk135': File exists
/bin/mknod: `/dev/fbsnap135': File exists
/bin/mknod: `/dev/fbdisk136': File exists
/bin/mknod: `/dev/fbsnap136': File exists
/bin/mknod: `/dev/fbdisk137': File exists
/bin/mknod: `/dev/fbsnap137': File exists
/share/HDA_DATA/Public
/bin/mknod: `/dev/fbdisk138': File exists
/bin/mknod: `/dev/fbsnap138': File exists
/bin/mknod: `/dev/fbdisk139': File exists
/bin/mknod: `/dev/fbsnap139': File exists
/bin/mknod: `/dev/fbdisk140': File exists
/bin/mknod: `/dev/fbsnap140': File exists
/bin/mknod: `/dev/fbdisk141': File exists
/bin/mknod: `/dev/fbsnap141': File exists
/bin/mknod: `/dev/fbdisk142': File exists
/share/HDA_DATA/Qusb
/bin/mknod: `/dev/fbsnap142': File exists
/bin/mknod: `/dev/fbdisk143': File exists
/bin/mknod: `/dev/fbsnap143': File exists
/bin/mknod: `/dev/fbdisk144': File exists
/bin/mknod: `/dev/fbsnap144': File exists
Starting NFS mountd. Mountd port number assigned automatically.
/bin/mknod: `/dev/fbdisk145': File exists
/share/HDA_DATA/Qweb
/bin/mknod: `/dev/fbsnap145': File exists
/bin/mknod: `/dev/fbdisk146': File exists
/bin/mknod: `/dev/fbsnap146': File exists
/share/HDA_DATA/Qmultimedia
/bin/mknod: `/dev/fbdisk147': File exists
/bin/mknod: `/dev/fbsnap147': File exists
/bin/mknod: `/dev/fbdisk148': File exists
/bin/mknod: `/dev/fbsnap148': File exists
/bin/mknod: `/dev/fbdisk149': File exists
/bin/mknod: `/dev/fbsnap149': File exists
/bin/mknod: `/dev/fbdisk150': File exists
/share/HDA_DATA/Qdownload
/bin/mknod: `/dev/fbsnap150': File exists
/bin/mknod: `/dev/fbdisk151': File exists
/bin/mknod: `/dev/fbsnap151': File exists
/bin/mknod: `/dev/fbdisk152': File exists
/bin/mknod: `/dev/fbsnap152': File exists
Q105B01403/bin/mknod: `/dev/fbdisk153': File exists
/bin/mknod: `/dev/fbsnap153': File exists
/bin/mknod: `/dev/fbdisk154': File exists
/bin/mknod: `/dev/fbsnap154': File exists
Starting NFS daemon: rpc.nfsd
/bin/mknod: `/dev/fbdisk155': File exists
/bin/mknod: `/dev/fbsnap155': File exists
/bin/mknod: `/dev/fbdisk156': File exists
/bin/mknod: `/dev/fbsnap156': File exists
[ 197.310000] warning: process `pic_raw' used the deprecated sysctl system call with 8.1.2.
/bin/mknod: `/dev/fbdisk157': File exists
/bin/mknod: `/dev/fbsnap157': File exists
/bin/mknod: `/dev/fbdisk158': File exists
/bin/mknod: `/dev/fbsnap158': File exists
/bin/mknod: `/dev/fbdisk159': File exists
/bin/mknod: `/dev/fbsnap159': File exists
/bin/mknod: `/dev/fbdisk160': File exists
/bin/mknod: `/dev/fbsnap160': File exists
/bin/mknod: `/dev/fbdisk161': File exists
[ 198.240000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 198.250000] NFSD: starting 90-second grace period
/bin/mknod: `/dev/fbsnap161': File exists
/bin/mknod: `/dev/fbdisk162': File exists
/bin/mknod: `/dev/fbsnap162': File exists
sed: /home/httpd/cgi-bin/Qrecordings/help/*.html: No such file or directory
/bin/mknod: `/dev/fbdisk163': File exists
/bin/mknod: `/dev/fbsnap163': File exists
/bin/mknod: `/dev/fbdisk164': File exists
init_nas.sh: check_last_degrade_error storage_boot_init 5
/bin/mknod: `/dev/fbsnap164': File exists
Multimedia Station, /bin/mknod: `/dev/fbdisk165': File exists
/bin/mknod: `/dev/fbsnap165': File exists
storage_boot_init 5 ...
/bin/mknod: `/dev/fbdisk166': File exists
/bin/mknod: `/dev/fbsnap166': File exists
/bin/mknod: `/dev/fbdisk167': File exists
/bin/mknod: `/dev/fbsnap167': File exists
storage_boot_init.c: Drive 1 does not have any bad block.
init_nas.sh: set LED with storage_boot_init 4
/bin/mknod: `/dev/fbdisk168': File exists
/bin/mknod: `/dev/fbsnap168': File exists
/bin/mknod: `/dev/fbdisk169': File exists
storage_boot_init 4 ...
storage_boot_init.c: Set Status LED...
/bin/mknod: `/dev/fbsnap169': File exists
/bin/mknod: `/dev/fbdisk170': File exists
/bin/mknod: `/dev/fbsnap170': File exists
Starting NFS lockd status:[/sys/block/sda]
sh: /usr/bin/qcmd: No such file or directory
/bin/mknod: `/dev/fbdisk171': File exists
/bin/mknod: `/dev/fbsnap171': File exists
/bin/mknod: `/dev/fbdisk172': File exists
[/etc/config/runone/*] do nothing
/bin/mknod: `/dev/fbsnap172': File exists
/bin/mknod: `/dev/fbdisk173': File exists
/bin/mknod: `/dev/fbsnap173': File exists
.
/bin/mknod: `/dev/fbdisk174': File exists
/bin/mknod: `/dev/fbsnap174': File exists
/bin/mknod: `/dev/fbdisk175': File exists
/bin/mknod: `/dev/fbsnap175': File exists
/bin/mknod: `/dev/fbdisk176': File exists
/bin/mknod: `/dev/fbsnap176': File exists
/bin/mknod: `/dev/fbdisk177': File exists
/bin/mknod: `/dev/fbsnap177': File exists
/bin/mknod: `/dev/fbdisk178': File exists
/bin/mknod: `/dev/fbsnap178': File exists
/bin/mknod: `/dev/fbdisk179': File exists
/bin/mknod: `/dev/fbsnap179': File exists
/bin/mknod: `/dev/fbdisk180': File exists
/bin/mknod: `/dev/fbsnap180': File exists
Starting ddns update: /bin/mknod: `/dev/fbdisk181': File exists
/bin/mknod: `/dev/fbsnap181': File exists
/var/ddns_tmp.conf is not exist
/bin/mknod: `/dev/fbdisk182': File exists
[ 203.750000] rule type=2, num=0
/bin/mknod: `/dev/fbsnap182': File exists
/bin/mknod: `/dev/fbdisk183': File exists
/bin/mknod: `/dev/fbsnap183': File exists
/bin/mknod: `/dev/fbdisk184': File exists
/bin/mknod: `/dev/fbsnap184': File exists
/bin/mknod: `/dev/fbdisk185': File exists
/bin/mknod: `/dev/fbsnap185': File exists
/bin/mknod: `/dev/fbdisk186': File exists
/bin/mknod: `/dev/fbsnap186': File exists
/bin/mknod: `/dev/fbdisk187': File exists
/bin/mknod: `/dev/fbsnap187': File exists
/bin/mknod: `/dev/fbdisk188': File exists
/bin/mknod: `/dev/fbsnap188': File exists
/bin/mknod: `/dev/fbdisk189': File exists
/bin/mknod: `/dev/fbsnap189': File exists
/bin/mknod: `/dev/fbdisk190': File exists
/bin/mknod: `/dev/fbsnap190': File exists
/bin/mknod: `/dev/fbdisk191': File exists
/bin/mknod: `/dev/fbsnap191': File exists
/bin/mknod: `/dev/fbdisk192': File exists
/bin/mknod: `/dev/fbsnap192': File exists
/bin/mknod: `/dev/fbdisk193': File exists
WOL: disabled.
/bin/mknod: `/dev/fbsnap193': File exists
/bin/mknod: `/dev/fbdisk194': File exists
/bin/mknod: `/dev/fbsnap194': File exists
/bin/mknod: `/dev/fbdisk195': File exists
/bin/mknod: `/dev/fbsnap195': File exists
[ 206.080000] WOL disable
/bin/mknod: `/dev/fbdisk196': File exists
/bin/mknod: `/dev/fbsnap196': File exists
/bin/mknod: `/dev/fbdisk197': File exists
/bin/mknod: `/dev/fbsnap197': File exists
/bin/mknod: `/dev/fbdisk198': File exists
/bin/mknod: `/dev/fbsnap198': File exists
/etc/config/localtime is exist
/bin/mknod: `/dev/fbdisk199': File exists
/bin/mknod: `/dev/fbsnap199': File exists
chmod: /home/httpd/cgi-bin/quick/quick_info.cgi: No such file or directory
/bin/mknod: `/dev/fbdisk200': File exists
/bin/mknod: `/dev/fbsnap200': File exists
/bin/mknod: `/dev/fbdisk201': File exists
/bin/mknod: `/dev/fbsnap201': File exists
/bin/mknod: `/dev/fbdisk202': File exists
/bin/mknod: `/dev/fbsnap202': File exists
/bin/mknod: `/dev/fbdisk203': File exists
/bin/mknod: `/dev/fbsnap203': File exists
/bin/mknod: `/dev/fbdisk204': File exists
/bin/mknod: `/dev/fbsnap204': File exists
/bin/mknod: `/dev/fbdisk205': File exists
/bin/mknod: `/dev/fbsnap205': File exists
/bin/mknod: `/dev/fbdisk206': File exists
/bin/mknod: `/dev/fbsnap206': File exists
/bin/mknod: `/dev/fbdisk207': File exists
/bin/mknod: `/dev/fbsnap207': File exists
/bin/mknod: `/dev/fbdisk208': File exists
/bin/mknod: `/dev/fbsnap208': File exists
/bin/mknod: `/dev/fbdisk209': File exists
/bin/mknod: `/dev/fbsnap209': File exists
/bin/mknod: `/dev/fbdisk210': File exists
/bin/mknod: `/dev/fbsnap210': File exists
/bin/mknod: `/dev/fbdisk211': File exists
/bin/mknod: `/dev/fbsnap211': File exists
/bin/mknod: `/dev/fbdisk212': File exists
/bin/mknod: `/dev/fbsnap212': File exists
/bin/mknod: `/dev/fbdisk213': File exists
/bin/mknod: `/dev/fbsnap213': File exists
/bin/mknod: `/dev/fbdisk214': File exists
/bin/mknod: `/dev/fbsnap214': File exists
/bin/mknod: `/dev/fbdisk215': File exists
disabled.
/bin/mknod: `/dev/fbsnap215': File exists
/bin/mknod: `/dev/fbdisk216': File exists
/bin/mknod: `/dev/fbsnap216': File exists
/bin/mknod: `/dev/fbdisk217': File exists
/bin/mknod: `/dev/fbsnap217': File exists
/bin/mknod: `/dev/fbdisk218': File exists
/bin/mknod: `/dev/fbsnap218': File exists
/bin/mknod: `/dev/fbdisk219': File exists
/bin/mknod: `/dev/fbsnap219': File exists
/bin/mknod: `/dev/fbdisk220': File exists
/bin/mknod: `/dev/fbsnap220': File exists
/bin/mknod: `/dev/fbdisk221': File exists
/bin/mknod: `/dev/fbsnap221': File exists
/bin/mknod: `/dev/fbdisk222': File exists
/bin/mknod: `/dev/fbsnap222': File exists
/bin/mknod: `/dev/fbdisk223': File exists
radiusd is disabled.
/bin/mknod: `/dev/fbsnap223': File exists
/bin/mknod: `/dev/fbdisk224': File exists
/bin/mknod: `/dev/fbsnap224': File exists
Initailize ldap server config file
/bin/mknod: `/dev/fbdisk225': File exists
/bin/mknod: `/dev/fbsnap225': File exists
/bin/mknod: `/dev/fbdisk226': File exists
/bin/mknod: `/dev/fbsnap226': File exists
/bin/mknod: `/dev/fbdisk227': File exists
Initailize ntp config file
/bin/mknod: `/dev/fbsnap227': File exists
/bin/mknod: `/dev/fbdisk228': File exists
/bin/mknod: `/dev/fbsnap228': File exists
/bin/mknod: `/dev/fbdisk229': File exists
/bin/mknod: `/dev/fbsnap229': File exists
/bin/mknod: `/dev/fbdisk230': File exists
/bin/mknod: `/dev/fbsnap230': File exists
/bin/mknod: `/dev/fbdisk231': File exists
/bin/mknod: `/dev/fbsnap231': File exists
Starting LDAP server service:
Shutting down UPS monitoring:Network UPS Tools - UPS driver controller 2.2.2
Can't open /var/lock/usbhid-ups-ttyS1.pid: No such file or directory
/bin/mknod: `/dev/fbdisk232': File exists
/bin/mknod: `/dev/fbsnap232': File exists
/bin/mknod: `/dev/fbdisk233': File exists
/bin/mknod: `/dev/fbsnap233': File exists
/bin/mknod: `/dev/fbdisk234': File exists
pptpd is disabled.
Starting iSCSI initiator service:
/bin/mknod: `/dev/fbsnap234': File exists
/bin/mknod: `/dev/fbdisk235': File exists
/bin/mknod: `/dev/fbsnap235': File exists
/bin/mknod: `/dev/fbdisk236': File exists
/bin/mknod: `/dev/fbsnap236': File exists
/bin/mknod: `/dev/fbdisk237': File exists
[ 214.220000] Loading iSCSI transport class v2.0-871.
/bin/mknod: `/dev/fbsnap237': File exists
/bin/mknod: `/dev/fbdisk238': File exists
DB version match
/bin/mknod: `/dev/fbsnap238': File exists
openvpn init.
/bin/mknod: `/dev/fbdisk239': File exists
slapd is disabled.
/bin/mknod: `/dev/fbsnap239': File exists
/bin/mknod: `/dev/fbdisk240': File exists
/bin/mknod: `/dev/fbsnap240': File exists
/bin/mknod: `/dev/fbdisk241': File exists
/bin/mknod: `/dev/fbsnap241': File exists
/bin/mknod: `/dev/fbdisk242': File exists
/bin/mknod: `/dev/fbsnap242': File exists
[ 215.890000] iscsi: registered transport (tcp)
/bin/mknod: `/dev/fbdisk243': File exists
/bin/mknod: `/dev/fbsnap243': File exists
/bin/mknod: `/dev/fbdisk244': File exists
/bin/mknod: `/dev/fbsnap244': File exists
/bin/mknod: `/dev/fbdisk245': File exists
/bin/mknod: `/dev/fbsnap245': File exists
/bin/mknod: `/dev/fbdisk246': File exists
/bin/mknod: `/dev/fbsnap246': File exists
/bin/mknod: `/dev/fbdisk247': File exists
/bin/mknod: `/dev/fbsnap247': File exists
/bin/mknod: `/dev/fbdisk248': File exists
/bin/mknod: `/dev/fbsnap248': File exists
/bin/mknod: `/dev/fbdisk249': File exists
/bin/mknod: `/dev/fbsnap249': File exists
/bin/mknod: `/dev/fbdisk250': File exists
/bin/mknod: `/dev/fbsnap250': File exists
/bin/mknod: `/dev/fbdisk251': File exists
/bin/mknod: `/dev/fbsnap251': File exists
[ 218.360000] nfsd: last server has exited, flushing export cache
/bin/mknod: `/dev/fbdisk252': File exists
/bin/mknod: `/dev/fbsnap252': File exists
/bin/mknod: `/dev/fbdisk253': File exists
/bin/mknod: `/dev/fbsnap253': File exists
/bin/mknod: `/dev/fbdisk254': File exists
/bin/mknod: `/dev/fbsnap254': File exists
/bin/mknod: `/dev/fbdisk255': File exists
/bin/mknod: `/dev/fbsnap255': File exists
Starting LUN Porter manitor: lunportman...
storage_boot_init 8 ...
killall: usbhid-ups: no process killed
openvpn init OK !.
openvpn is disabled.
.
Music Station, Starting UPS monitoring:mv: unable to rename `/mnt/ext/opt/DSv3/opt/gt': Directory not empty
crond[3497]: failed user admin parsing [global]
crond[3497]: failed user admin parsing workgroup = elements
crond[3497]: failed user admin parsing security = USER
crond[3497]: failed user admin parsing server string = qnap NAS
crond[3497]: failed user admin parsing username level = 0
crond[3497]: failed user admin parsing null passwords = yes
crond[3497]: failed user admin parsing socket options = TCP_NODELAY SO_KEEPALIVE SO_SNDBUF=65536 SO_RCVBUF=65536
crond[3497]: failed user admin parsing os level = 20
crond[3497]: failed user admin parsing preferred master = no
Network UPS Tools - UPS driver controller 2.2.2
Starting BT management services:
Network UPS Tools: 0.29 USB communication driver - core 0.33 (2.2.2)
No matching HID UPS found
Driver failed to start (exit status=1)
Network UPS Tools upsd 2.2.2
rpcbind: cannot create socket for udp6
rpcbind: cannot create socket for tcp6
task_queue_position existed in BT_TASK.
Network UPS Tools - UPS driver controller 2.2.2
Network UPS Tools: 0.29 USB communication driver - core 0.33 (2.2.2)
No matching HID UPS found
Driver failed to start (exit status=1)
task_move_folder existed in BT_TASK.
disabled
disabled
restart atalk....rpcbind: cannot create socket for udp6
rpcbind: cannot create socket for tcp6
task_move_folder existed in HTTP_FTP_TASK.
task_hash existed in BT_TASK.
task_type existed in BT_TASK.
[ 244.930000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 244.940000] NFSD: starting 90-second grace period
task_magnet_link existed in BT_TASK.
[I] Mount options = allow_other,max_item=256,iocharset=UTF-8
[I] Charset : successfully initialised charset='UTF-8'
pause_all_time existed in BT_SESSION.
Photo Station. task_savename existed in HTTP_FTP_TASK.
task_queue_position existed in HTTP_FTP_TASK.
Scan torrent and check the data of bt database...
gt process count = 1
started gt in BUILT-IN mode.
Welcome to TS-110(192.168.81.214), QNAP Systems, Inc.
silicon login: crond[3497]: failed user admin parsing [global]
crond[3497]: failed user admin parsing workgroup = elements
crond[3497]: failed user admin parsing security = USER
crond[3497]: failed user admin parsing server string = qnap NAS
crond[3497]: failed user admin parsing username level = 0
crond[3497]: failed user admin parsing null passwords = yes
crond[3497]: failed user admin parsing socket options = TCP_NODELAY SO_KEEPALIVE SO_SNDBUF=65536 SO_RCVBUF=65536
crond[3497]: failed user admin parsing os level = 20
crond[3497]: failed user admin parsing preferred master = no
HP ProLiant ML110 G7に32GBのメモリーを搭載する
HP ProLiant ML110 G7 Server Maintenance and Service Guide の62ページ目には、以下のように記載されている。 General DIMM slot population guidelines Th...
-
Arvel USBシリアルケーブルSRC06-USBをWindows 10 x86_64で使う で、Arvel (現バッファロー) のSRC06-USBというFTDIのチップを使ったUSB to Rs-232CアダプターをWindows 10で使う話を書いたが、同じSRC...
-
※ Windows 11でも使える記事 を書いた。 Arvel SRC06-USB USBシリアルケーブルというUSBシリアル変換器を持っている。 これにはFDTI製のUSBシリアル変換チップをい利用していて、USB VendorID/ProductID=0x...
-
This post will be irrelevant for Google Workspace after 2022-10-04 because OAuth out-of-band (OBB) flow will be deprecated. See my newe...
