HP ProLiant ML110 G7 Server Maintenance and Service Guideの62ページ目には、以下のように記載されている。
General DIMM slot population guidelines
- The server has four memory slots.
- The server supports two channels with two UDIMM slots per channel.
- Memory channel A consists of the two UDIMMs that are closest to the processor.
- Memory channel B consists of the two UDIMMs that are located farthest from the processor.
- Different types of processors have different types of memory support.
- The server supports dual-rank, 1,333 MT/s ECC UDIMMs.
- The server supports up to 16 GB (4x4-GB) for UDIMMs.
つまり、4GBのECC Unbuffered DIMM 4枚で、16GBがメモリー上限容量ということになっている。 だが、8GBのECC Unbuffered DIMM 4枚を挿してみたことろ、32GBのメモリーとして問題なく認識された。 PC3とPC3Lそれぞれ2枚ずつしか手元になかったのだが、この構成でも問題なかった。 もちろん、PC3 2枚、PC3L 2枚で、それぞれ組にして挿してある。
CPUも、購入時にIntel CeleronからIntel Xeon E31220に換装してある。 高負荷になるマシンではないのだが、手頃な価格で入手できたので、まだしばらく使い続けられそうだ。 NetBSD/amd64 11のdmesgは以下のようになった。
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
2024, 2025, 2026
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 11.0_STABLE (GENERIC) #0: Thu Sep 24 00:37:32 JST 2026
ryoon@ruthenium:/usr/world/11/amd64/obj/sys/arch/amd64/compile/GENERIC
total memory = 32733 MB
avail memory = 31640 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
mainbus0 (root)
ACPI: RSDP 0x00000000000F4F00 000024 (v02 HP )
ACPI: XSDT 0x00000000F1E34A80 0000A4 (v01 HP ProLiant 00000002 ?? 0000162E)
ACPI: FACP 0x00000000F1E34B80 0000F4 (v03 HP ProLiant 00000002 ?? 0000162E)
Firmware Warning (ACPI): Invalid length for FADT/Pm1aControlBlock: 32, using default 16 (20241212/tbfadt-850)
Firmware Warning (ACPI): Invalid length for FADT/Pm2ControlBlock: 32, using default 8 (20241212/tbfadt-850)
ACPI: DSDT 0x00000000F1E34C80 001A41 (v01 HP DSDT 00000001 INTL 20030228)
ACPI: FACS 0x00000000F1E34100 000040
ACPI: SPCR 0x00000000F1E34140 000050 (v01 HP SPCRRBSU 00000001 ?? 0000162E)
ACPI: MCFG 0x00000000F1E341C0 00003C (v01 HP ProLiant 00000001 00000000)
ACPI: HPET 0x00000000F1E34200 000038 (v01 HP ProLiant 00000002 ?? 0000162E)
ACPI: FFFF 0x00000000F1E34240 000064 (v02 HP ProLiant 00000002 ?? 0000162E)
ACPI: SPMI 0x00000000F1E342C0 000040 (v05 HP ProLiant 00000001 ?? 0000162E)
ACPI: ERST 0x00000000F1E34300 0001D0 (v01 HP ProLiant 00000001 ?? 0000162E)
ACPI: APIC 0x00000000F1E34500 000252 (v01 HP ProLiant 00000002 00000000)
ACPI: FFFF 0x00000000F1E34780 000176 (v01 HP ProLiant 00000001 ?? 0000162E)
ACPI: BERT 0x00000000F1E34900 000030 (v01 HP ProLiant 00000001 ?? 0000162E)
ACPI: HEST 0x00000000F1E34940 0000BC (v01 HP ProLiant 00000001 ?? 0000162E)
ACPI: DMAR 0x00000000F1E34A00 000070 (v01 HP ProLiant 00000001 ?? 0000162E)
ACPI: SSDT 0x00000000F1E36700 000125 (v03 HP CRSPCI0 00000002 HP 00000001)
ACPI: SSDT 0x00000000F1E36840 000573 (v03 HP riser0 00000002 INTL 20030228)
ACPI: SSDT 0x00000000F1E36DC0 00014B (v01 HP pcc 00000001 INTL 20090625)
ACPI: SSDT 0x00000000F1E36F40 0008D4 (v01 INTEL PPM RCM 80000001 INTL 20061109)
ACPI: 5 ACPI AML tables successfully acquired and loaded
ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 0x20, 24 pins
cpu0 at mainbus0 apid 0
cpu0: Use lfence to serialize rdtsc
cpu0: Intel(R) Xeon(R) CPU E31220 @ 3.10GHz, id 0x206a7
cpu0: node 0, package 0, core 0, smt 0
cpu1 at mainbus0 apid 2
cpu1: Intel(R) Xeon(R) CPU E31220 @ 3.10GHz, id 0x206a7
cpu1: node 0, package 0, core 1, smt 0
cpu2 at mainbus0 apid 4
cpu2: Intel(R) Xeon(R) CPU E31220 @ 3.10GHz, id 0x206a7
cpu2: node 0, package 0, core 2, smt 0
cpu3 at mainbus0 apid 6
cpu3: Intel(R) Xeon(R) CPU E31220 @ 3.10GHz, id 0x206a7
cpu3: node 0, package 0, core 3, smt 0
acpi0 at mainbus0: Intel ACPICA 20241212
acpi0: X/RSDT: OemId <HP ,ProLiant,00000002>, AslId < <2147483602>^D,0000162e>
acpi0: MCFG: segment 0, bus 0-63, address 0x00000000f4000000
acpi0: SCI interrupting at int 9
acpi0: fixed power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
ipmi_acpi0 at acpi0 (MI0, IPI0001-0): io 0xca2-0xca3
ipmi0 at ipmi_acpi0
attimer1 at acpi0 (TIME, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (BEEP, PNP0800): io 0x61
spkr0 at pcppi1: PC Speaker
wsbell at spkr0 not configured
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
com0 at acpi0 (COMA, PNP0501-0): io 0x3f8-0x3ff irq 4
com0: ns16550a, 16-byte FIFO
pckbc1 at acpi0 (KBD, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F13) (aux port): irq 12
acpitz0 at acpi0 (THM0): cpu0
acpitz0: levels: critical 31.3 C, passive 9.8 C, passive cooling
apei0 at acpi0: ACPI Platform Error Interface
apei0: BERT: OemId <HP ,ProLiant,00000001> AslId < <2147483602>^D,0000162e>
apei0: BERT: 0x40 bytes at 0xf1e3e000
apei0: BERT: no boot errors recorded
apei0: ERST: OemId <HP ,ProLiant,00000001> AslId < <2147483602>^D,0000162e>
apei0: ERST: 0 records in error log 0 bytes @ 0x0 attr=0#
apei0: HEST: OemId <HP ,ProLiant,00000001> AslId < <2147483602>^D,0000162e>
apei0: HEST: 3 hardware error sources
apei0: autoconfiguration error: HEST[0, Id=6]: unimplemented type: 0x0006
apei0: autoconfiguration error: HEST[1, Id=7]: unimplemented type: 0x0007
apei0: autoconfiguration error: HEST[2, Id=8]: unimplemented type: 0x0008
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: Intel Sandy Bridge (server) Host Bridge (rev. 0x09)
ppb0 at pci0 dev 1 function 0: Intel Sandy Bridge (desktop) PCIe Root port (rev. 0x09)
ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 5.0GT/s
pci1 at ppb0 bus 4
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci0 dev 6 function 0: Intel product 010d (rev. 0x09)
ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 5.0GT/s
pci2 at ppb1 bus 7
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ehci0 at pci0 dev 26 function 0: Intel 6 Series Chipset Family USB (rev. 0x05)
ehci0: 64-bit DMA
ehci0: interrupting at ioapic0 pin 21
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: Using DMA subregion for control data structures
usb0 at ehci0: USB revision 2.0
ppb2 at pci0 dev 28 function 0: Intel 6 Series Chipset Family PCIe Root Port 1 (rev. 0xb5)
ppb2: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 5.0GT/s
pci3 at ppb2 bus 10
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 28 function 4: Intel 6 Series Chipset Family PCIe Root Port 5 (rev. 0xb5)
ppb3: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
ppb3: link is x1 @ 2.5GT/s
pci4 at ppb3 bus 2
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
wm0 at pci4 dev 0 function 0, 64-bit DMA: Intel i82574L (rev. 0x00)
wm0: for TX and RX interrupting at msix0 vec 0 affinity to 1
wm0: for TX and RX interrupting at msix0 vec 1 affinity to 2
wm0: for LINK interrupting at msix0 vec 2
wm0: PCI-Express bus
wm0: 2048 words (8 address bits) SPI EEPROM, version 2.1.2, Image Unique ID ffffffff
wm0: ASPM L0s and L1 are disabled to workaround the errata.
wm0: RX packet buffer size: 20KB
wm0: Ethernet address XX:XX:XX:XX:XX:XX
wm0: 0x224040<SPI,PCIE,ASF_FIRM,WOL>
makphy0 at wm0 phy 1: Marvell 88E1149 Gigabit PHY, rev. 1
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb4 at pci0 dev 28 function 5: Intel 6 Series Chipset Family PCIe Root Port 6 (rev. 0xb5)
ppb4: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
ppb4: link is x1 @ 2.5GT/s
pci5 at ppb4 bus 3
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
wm1 at pci5 dev 0 function 0, 64-bit DMA: Intel i82574L (rev. 0x00)
wm1: for TX and RX interrupting at msix1 vec 0 affinity to 1
wm1: for TX and RX interrupting at msix1 vec 1 affinity to 2
wm1: for LINK interrupting at msix1 vec 2
wm1: PCI-Express bus
wm1: 2048 words (8 address bits) SPI EEPROM, version 2.1.0, Image Unique ID ffffffff
wm1: ASPM L0s and L1 are disabled to workaround the errata.
wm1: RX packet buffer size: 20KB
wm1: Ethernet address XX:XX:XX:XX:XX:XY
wm1: 0x224040<SPI,PCIE,ASF_FIRM,WOL>
makphy1 at wm1 phy 1: Marvell 88E1149 Gigabit PHY, rev. 1
makphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb5 at pci0 dev 28 function 6: Intel 6 Series Chipset Family PCIe Root Port 7 (rev. 0xb5)
ppb5: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
pci6 at ppb5 bus 13
pci6: i/o space, memory space enabled, rd/line, wr/inv ok
ppb6 at pci0 dev 28 function 7: Intel 6 Series Chipset Family PCIe Root Port 8 (rev. 0xb5)
ppb6: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
ppb6: link is x1 @ 2.5GT/s
pci7 at ppb6 bus 1
pci7: i/o space, memory space enabled, rd/line, wr/inv ok
Hewlett-Packard iLO3 Slave (miscellaneous system, revision 0x05) at pci7 dev 0 function 0 not configured
vga0 at pci7 dev 0 function 1: Matrox MGA G200eH (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
Hewlett-Packard iLO3 Management (miscellaneous system, revision 0x05) at pci7 dev 0 function 2 not configured
uhci0 at pci7 dev 0 function 4: Hewlett-Packard iLO3 Virtual USB (rev. 0x02)
uhci0: interrupting at msi2 vec 0
usb1 at uhci0: USB revision 1.0
ehci1 at pci0 dev 29 function 0: Intel 6 Series Chipset Family USB (rev. 0x05)
ehci1: 64-bit DMA
ehci1: interrupting at ioapic0 pin 20
ehci1: BIOS has given up ownership
ehci1: EHCI version 1.0
ehci1: Using DMA subregion for control data structures
usb2 at ehci1: USB revision 2.0
ppb7 at pci0 dev 30 function 0: Intel 82801BA Hub-PCI Bridge (rev. 0xa5)
pci8 at ppb7 bus 19
pci8: i/o space, memory space enabled
ichlpcib0 at pci0 dev 31 function 0: Intel C204 LPC (rev. 0x05)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
tco0 at ichlpcib0: TCO (watchdog) timer configured.
tco0: autoconfiguration error: TCO timer reboot disabled by hardware; hope SMBIOS properly handles it.
tco0: Min/Max interval 1/367 seconds
ahcisata0 at pci0 dev 31 function 2: Intel 6 Series Chipset Family AHCI 1 (rev. 0x05)
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.30, 6 ports, 32 slots, CAP 0xff32ff45<EMS,PSC,SSC,PMD,SPM,ISS=0x3=Gen3,SCLO,SAL,SALP,SSS,SMPS,SSNTF,SNCQ,S64A>
ahcisata0: interrupting at msi3 vec 0
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 2
atabus3 at ahcisata0 channel 3
atabus4 at ahcisata0 channel 4
atabus5 at ahcisata0 channel 5
isa0 at ichlpcib0
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 16-byte FIFO
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat 1 us, pow 1000 mW
coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=94
acpicpu1 at cpu1: ACPI CPU
coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=94
acpicpu2 at cpu2: ACPI CPU
coretemp2 at cpu2: thermal sensor, 1 C resolution, Tjmax=94
acpicpu3 at cpu3: ACPI CPU
coretemp3 at cpu3: thermal sensor, 1 C resolution, Tjmax=94
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 3092973000 Hz quality 3000
IPsec: Initialized Security Association Processing.
uhub0 at usb0: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb2: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb1: NetBSD (0x0000) UHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ahcisata0 port 0: device present, speed: 6.0Gb/s
ahcisata0 port 1: device present, speed: 6.0Gb/s
ahcisata0 port 2: device present, speed: 3.0Gb/s
ahcisata0 port 3: device present, speed: 3.0Gb/s
ahcisata0 port 5: device present, speed: 3.0Gb/s
uhub3 at uhub1 port 1: vendor 8087 (0x8087) product 0024 (0x0024), class 9/0, rev 2.00/0.00, addr 2
uhub3: single transaction translator
uhub4 at uhub0 port 1: vendor 8087 (0x8087) product 0024 (0x0024), class 9/0, rev 2.00/0.00, addr 2
uhub4: single transaction translator
uhub3: 6 ports with 6 removable, self powered
uhub4: 6 ports with 6 removable, self powered
wd0 at atabus0 drive 0
wd0: <LITEONIT LCS-128M6S>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 119 GB, 248085 cyl, 16 head, 63 sec, 512 bytes/sect x 250069680 sectors
wd0: GPT GUID: 9c5f3319-b7f3-4f30-ade0-d98e9c91d02d
dk0 at wd0: "ROOT", 233292397 blocks at 64, type: ffs
dk1 at wd0: "SWAP", 16777167 blocks at 233292480, type: swap
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), NCQ (32 tags)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags)
wd1 at atabus1 drive 0
wd1: <WDC WD80EFAX-68KNBN0>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 7452 GB, 15504021 cyl, 16 head, 63 sec, 512 bytes/sect x 15628053168 sectors (4096 bytes/physsect)
wd1: GPT GUID: 6c8c32f9-0ba2-4656-a829-43cda8d023e0
dk2 at wd1: "b2", 15628053101 blocks at 34, type: ffs
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags) w/PRIO
wd1(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags) w/PRIO
wd2 at atabus2 drive 0
wd2: <ST16000NE000-2RW103>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 14902 GB, 31003729 cyl, 16 head, 63 sec, 512 bytes/sect x 31251759104 sectors (4096 bytes/physsect)
wd2: GPT GUID: dd462515-2c6b-4dae-b9d0-2753fee78541
dk3 at wd2: "a3", 31251759037 blocks at 34, type: ffs
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags)
wd2(ahcisata0:2:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags)
wd3 at atabus3 drive 0
wd3: <WDC WD120EFBX-68B0EN0>
wd3: drive supports 16-sector PIO transfers, LBA48 addressing
wd3: 11176 GB, 23251756 cyl, 16 head, 63 sec, 512 bytes/sect x 23437770752 sectors (4096 bytes/physsect)
wd3: GPT GUID: 1b5551e4-a0bc-4700-bd7c-e19d6f92e67e
dk4 at wd3: "c", 23437770685 blocks at 34, type: ffs
wd3: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags) w/PRIO
wd3(ahcisata0:3:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags) w/PRIO
wd4 at atabus5 drive 0
wd4: <Synology HAT3310-16T>
wd4: drive supports 16-sector PIO transfers, LBA48 addressing
wd4: 14902 GB, 31003729 cyl, 16 head, 63 sec, 512 bytes/sect x 31251759104 sectors (4096 bytes/physsect)
wd4: GPT GUID: ccc36f52-cb33-4402-a6b9-37671161b92d
dk5 at wd4: "d", 31251759037 blocks at 34, type: ffs
wd4: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags) w/PRIO
wd4(ahcisata0:5:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags) w/PRIO
swwdog0: software watchdog initialized
WARNING: 4 errors while detecting hardware; check system log.
boot device: wd0
root on dk0 dumps on dk1
root file system type: ffs
kern.module.path=/stand/amd64/11.0/modules
ipmi0: version 32.0 interface KCS iobase 0xca2/0x2 spacing 1
ipmi0: ID 19.1 IPMI 2.0 Available
ipmi0: Additional Chassis FRU SEL SDR Sensor
ipmi0: Manufacturer 0000b Product 200b
ipmi0: Firmware 1.94
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
0 件のコメント:
コメントを投稿
注: コメントを投稿できるのは、このブログのメンバーだけです。